Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi.
I am using nRF52832 and SDK15, S132 Softdevice.
I integrated the uart example in the ble_peripheral folder with the buttonless_dfu example, and added the passkey....
Hello
I have just started development for the nRF52480 preview development kit.
I am powering the dev kit through USB on J2 (with power switch set to VDD).
I want...
Hi Everyone
I have written a code using the peripheral template given in Nordic\nRF5_SDK_15.0.0_a53641a\examples\peripheral path which works very well so far.
My aim...
Hi all:
Q:When i reboot the board which burn the serial project , how to add the device key to serial board again?
I use PYACI to control the board which burn the serial...
Hi,
I have couple of question regarding ble_app_hrs_freertos example (sdk 14.2)
Possible bug - in main() , erase_bonds is a local variable (defined on the stack)....
Hi!
1. Is there any method to make paring and bonding without radio channel? For ex. write any data directly to .hex to periph and central devices.
2. Is it possible to...
Hi Everyone
I have added all the required paths for the ble_app_uart example but the program can not find the files like ble_advertising.h and nrf_sdh.h files which are...
hi support
Thinking of attendance system using bluetooth Identity cards
what is maximum nos of cards can a nrf52 scan at a time.
suppose there are 100people in a room...
I have just received my development kit and following the getting started instructions on website. But I am stuck at point 7 of this link https://www.nordicsemi.com/eng/Products...
hello Nordic team
I am using nrf52DK.how to use spi to read /write data .I have seen sdk14.2.0 in folder nRF5_SDK_14.2.0_17b948a\examples\peripheral\spi.
I am trying to interface an atmega32 with an nRF24L01. I am trying to communicate between two nRF's. But before proceeding to that, I set out to test the SPI connection between...
I put the nrf_ble_ancs_c_request_attrs in the BLE_ANCS_C_EVT_NOTIF event(added). But only return back 1 or 2 BLE_ANCS_C_EVT_NOTIF_ATTRIBUTE event. I am using 12.3.0 SDK example...
Hello,
This in reference to Case ID: 121570.
We are developing a wearable device with NRF52 as a Beacon with CR2032 coin cell battery from Panasonic. We have calculated...
i am using my custom board with nrf51822 and using sdk 12.3.0 .
the led blink example works fine on it but when i upload ble_app_uart then bluetooth is not advertising.
Hi i just get nRF52832 PCA10400 DK.
I am using SDK14.0.0. i tried to use /example/peripheral/spi.
i don't set the gpio set and high or low.in the SDK14.0.0, how to set...
