Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hello All,
I'm trying to build a receiving unit using the nRF24L01+ and PIC16F628A. Im using an nRF24L01+ and RaspberryPi as my TX unit which i managed to get working ...
Hi,
We have a device using the S110 v6.0.0 softdevice and the SDK v5.2.0.
We started working from the Proximity application available in the sdk.
Is it possible to...
Hello,
I'd like to evaluate the performance of an L2CAP CoC on the nRF52840. I was hoping to find an example project which uses this feature but I couldn't see one.
Is...
Hello,
I'm attempting to test the maximum throughput of the nRF52810 using S112 v6.0.0.
The Soft Device Spec v2.0 for S112 implies in Section 15.7 that there is a mechanism...
Hello I am using the nRF52832 in an application where it will be exposed to high magnetic field strengths (e.g. 30,000 Gauss) during normal use. I wanted to know if there...
Hello,
In my project, there is a need to use a service to transfer body temperature. For this I would like to use the standard body temperature service - Health Thermometr...
Hello DevZone,
I am doing a simple test for SPI communication between nRF52840 DK(SPI master) and Arduino UNO(slave).
The Nordic program is based on SDK 14.2.0 spi example...
Hi Support Team,
I used SDK14.1 with nrf52840 on PCA10056. I have a controller which was based on pc-ble-driver running on the host, and a target which was based on ble_connectivity...
Hello!
I have a problem with MQTT Publisher example on my nrf52840 DK.
here is my steps:
1. I edit nrf52840 mqtt example code with
Edit my MQTT settings with:
...
I wonder nrf52832 booting sequence detail.
I knew the booting sequence is MBR -> softdevice->bootloader->application.(is it right?)
but i am not sure how to work MBR and...
I am developing based on "nRF5_SDK_15.0.0_a53641a" [Ble_app_uart], but I am not using LOG in my development environment. If LOG related items in "sdk_config.h" are invalid...
[Ble_app_uart] of the old version of [nRF5_SDK_14.2.0_17 b948 a] is operating correctly, not due to the low-speed clock.
In the old version, the operation of the crystal setting...
I'm trying to get the TWIM peripheral up and running on a custom board with an NRF52810 running SDK15 and S112.
My board is properly advertising, and publishing our custom...
After nightmares with Eclipse I managed to setup Segger within 5 minutes and flash, using the guide from here .
That guide show a lot of very specific stuff you have to...
I have the following ADC code: bitbucket.org/.../eakpq
I have been trying for the past few days to get this code to just perform a single ADC scan, on five channels, once...
