Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hello All,
I'm trying to build a receiving unit using the nRF24L01+ and PIC16F628A. Im using an nRF24L01+ and RaspberryPi as my TX unit which i managed to get working ...
Hi,
We have a device using the S110 v6.0.0 softdevice and the SDK v5.2.0.
We started working from the Proximity application available in the sdk.
Is it possible to...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hi all,
My configuration:
nrf52832 microcontroller
Softdevice S132 V4.0.2
Nordic SDK 13.0
I'm using an "app_timer" in repeated mode with 10Hz frequency...
I have recently acquired a NAND chip from Micron and would like to use it for storage.
However, looking through the datasheet I found out that the addressing scheme require...
I'm planning using nRF52810 for a new product to reduce the power consumption.
But i worried whether old smartphone with Bluetooth4.0, like Iphone5s can connect with equipment...
I am dealing with the nRF24L01 to develop a remote controller. When I read the specification, I found a specification item, called C/ICO, with a typical value of 12dB in the...
hello,
I'm trying to send long (73B) data on a given characteristic using Android client as the central.
I well received:
USER_MEM_REQUEST OK
> #define...
Hi to everyone!
I'm following this guide to learn how to use secure DFU on a nRF52832DK board.
All steps have been done successfully, or I think so, until I reach the...
I want to find the agent of China, please, thanks
About Bluetooth and 2.4G, nRF52840/nRF52832/nRF52810
(The agent can provide some technical support and sales)
Can someone please explain the below line mentioned in NRF5 Serial port abstraction layer documentation.
Do not use synchronous API (timeout_ms
parameter > 0) in IRQ...
Hi there,
I want to flash nrf51 firmware from another MCU which is connected to nrf51 with UART interface.
I have seen dual bank serial bootloader examples, in that firmware...
Hi,
I know this has been touched on in other posts but I can't find a definitive answer.
I am making a product that sends data from a handheld joystick to a base station...
Hi All!
we are trying to tune Antenna use DTM over UART from examples.
It is works fine for AAAA IC but doesnot for AABB IC.
Why, what's possible problem?
thx...
Hi everyone,
My configuration:
nrf52832 microcontroller
Softdevice S132 V4.0.2
Nordic SDK 13.0
I need to develop a repetitive task with 10 Hz frequency...
Hi
I am trying to use the serial bootloader to upgrade nrf52 application, but I get verification failure.
I am using nrf52832 with SDK 13.0.0 & S132 SoftDevice v4.0...
Hi,
(1) I look for some methods that suggests is application flag to record. but I set this ble_adv_on_disconnect_disabled = false;. How do I check ble state when disconnect...
Hi
I'm trying to write data to flash and access it via declared const variable.
I can't use UICR because we are on NRF51 and this does not allow to change data in UICR...
