Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hello All,
I'm trying to build a receiving unit using the nRF24L01+ and PIC16F628A. Im using an nRF24L01+ and RaspberryPi as my TX unit which i managed to get working ...
Hi,
We have a device using the S110 v6.0.0 softdevice and the SDK v5.2.0.
We started working from the Proximity application available in the sdk.
Is it possible to...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hi I am trying to develop a an application to send data packets over ble using nordic uart service. I wanted to know what is the maximum bytes of data that I can send in one...
Hi,
I'm trying to integrate Bluetooth pairing code from experimental_ble_app_hrs_nfc_pairing example into ble_app_uart example (I have a project based on this example,...
Dear Nordic Team,
I want to know if we can support the real time talking like phone call between peripheral and central by software device. On application layer, we just...
As I have provision a nearby light server, use those serial commands:
In [1]: p = Provisioner(d[0])
In [2]: p.scan_start()
In [3]: p.provision()
How to provision...
I'm building wih Keil MDK-Lite Version 5.24.1 and I just copied the examples for gpiote into my own folder, everything was kept the same (ie copying from C:\Nordic\nRF5_SDK_14...
Hello. I tried to use UART speed 115200. But my slave does not response. I connected slave to the arduino and it is working corectly. I got 2 oscillograms . From arduino and...
Hello everyone,
Currently I'm altering the "ble_app_uart" and "ble_app_uart_c" examples (both under examples/ble_peripheral) to suit my needs. What I currently need to...
Hello,
I have interfaced one sensor with pca10040. I am using sdk 12.2.2. I am sending the data from sensor in advertisement packet(manuf specific data). Now my sensor data...
after the advertising timeout occurs the board goes into sleep mode and then immediately runs from the top of the main function. I know that a pin state change can wake up...
Edit: Rephrased the question to make it easier to answer.
I used flash storage to store a couple of variables between resets in a app made from SDK 12.2, now I am attempting...
hi,
i need to reconfigure the WDT and also change the timer value in WDT. is it possible to do that.
i tried but i can not.
1.configured wdt with timer 5sec.
2.i...
Hi guys,
we are developing firmware for nrf52832 SoC based on the mbed platform.
The firmware uses BLE and few peripherals (timers and pwms). Since our goal is to build...
Is it possible to scan and make Gatt Connection simulataneously from Android app to NRF device.I have seen issues in second connection after disconnection.I have seen second...
Question for I2S.
Execute follow.
[TXD.PTR set A] 1st
[START]
[TXPTRUPD event] (not set TXD.PTR) 2nd.
2nd transfer address use A?
How long time between...
There are a few setting options I would like to keep through power cycle like sensor sampling rate, continuous sampling on/off, etc. I had success implementing saving of one...
