hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Greetings,
There is a bit of strange operation in UARTE peripheral in nrf52832 with the DK. In the simple code below, if both of the if statements with comments 'Check 1...
Hello everyone,
I have a strange issue with s110 + whitelisting + Device Manager + nrf51822 + GCC and hopefully you can help me with a good advice. It appears that the...
hi,
I am trying to integrate buttonless switch to boot loader as explained in the documentation and the hrs experimental example.
I am working on SDK7.2.0 and using...
Hello,
I installed the new nrfjprog but it fails to write my nrf51 dongle:
ERROR: nrfjprog failed for an unknown reason. Run the same command again with
ERROR: argument...
Hi All,
I would like to design a wireless system using nRF51822 with an effective range >100m LoS and 5m under water.The system is used as a ON-OFF control device powered...
I am trying to run an Arduino sketch using the RedBearLab nRF51822. The sketch is designed to transfer data to and from a microprocessor and an Android device via bluetooth...
I'm currently want to use the NVM with ble device, when I tried to send values from the mobile app to be stored to the NVM, it doesn't work, I guessed that the problem that...
I want to write a device ID to the UICR registers at the same time as I flash the app code. I don't use Keil or that nrfproj.exe thing, I'm on a Mac. I have these targets...
Dear Nordic team,
I have the nRF51-Dongle and would like to use it with master control panel.
I did everything like already recommended in this tutorial .
The problem...
SDK 9.0
nRF51
PCA10028
I want use nRF51 gazell function one host multi device. Reference example code "gzp_dynamic_pairing",host and device can auto pairing .
But in host...
I used to be able to see my development kit in nRFgo studio and flashed S110 onto the chip. Now all I see is: "No boards connected". I am still able to flash programs onto...
Hey Guys，
Who can tell me what are the differences between the timer0, timer1 and timer2?
And if I want to set up timer interrupt in timer mode, the interrupt will be...
Hi everyone,
I took the example Ble_app_uart and I modified the Nus service for send data in Indicate mode.
With MCP I discover service and enable service (0x02->indicate...
Hi, every one,
In my application , we need to bond my device with host , and then our application will go to deep sleep by calling sd_power_system_off. When I wake up my...
