Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
I'm trying to connect to/program my nrf51822 module I just got. I've got it set up with my st-link but whenever I try to flash the device I keep getting: Error: Flash Download...
I'm trying to enable basic commands with my device. Ideally I have a terminal open on a mac running nodejs or use the UART subapp in the nRF Toolbox App, type a special command...
What's the proper way to debug what's causing my eval board to reset? I'm assuming I need to put a breakpoint in the hard fault handle, but how do I trace that back to the...
Hi,
as a university project, I am currently developing a ultra-low-power temperature and barometer sensor powered just by RF and laser-beam energy. Please see this link...
Is there any document that describes what has to be done in the App code to migrate from i.e. SDK v7.2 to the latest 8.1.1? I could not find it.
Ideally it would be nice...
I try to add a custom characteristic value's UUID. I couldn't find any example or document that provide this information. All I can find is a function sd_ble_gatts_descriptor_add...
As I run through the examples for the nRF51 S110 SDK , I'm not seeing anything for communicating with a sensor over I2C.
On a secondary note, since I have the option to...
I am using a nRF51422 (SDK 6.1.0 with S310) and i have a question about th UART.
I can send and receive data from/to an other MCU but i have to set different parameters...
Hi,
I recently started learning to program nRF51 development kit. I followed most of the examples listed in the forums but I am unable to find a dedicated link which would...
Hello,
I have made some modifications to the OTA DFU bootloader provided by nordic and would like to some advice. I went down this design path before nordic released the...
I was disappointed to see from this question that when calling sd_ble_gatts_characteristic_add(), the value of the characteristic is copied to the SD's memory region:
devzone...
Can anyone explain what that error code is meant to mean?
With the example sdk7.1 dfu bootloader, hrs_with_dfu app built unmodified and sd110 7.1, I get this error on attempting...
Hello,
I have a BLE application running on a nRF51822 chip with the S120 softdefice. If I use the standard Android "search for device" mechanism for Bluetooth devices,...
There seems to be 3 different libraries that can be used to access TWI: nrf_drv_twi, twi_hw_master, twi_sw_master. (please correct if i am wrong).
i am using SDK8.1. Which...
