Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi
I have a question about using gazell link layer and paring library with concurrent timeslot api. I try to do this but i have the hard fault handler after invoked nrf_gzll_init...
Hi,
From the documentation for the sd_ble_gap_sec_info_reply() function,
"This function is only used to reply to a BLE_GAP_EVT_SEC_INFO_REQUEST, calling it at other times...
Dear Madame/Sir
From my client I received nRF51822 DK.
See att file.
I do not see Product Key for DK
How can you solve the problem ?
Redards
Valeri Tosev
Hi, what I did is wrote below:
1/ I program the S120 softdevice to the nRF51822 board, using nRFgo studio software(the softdevice size is set to 80KB).
2/ I complied the...
Hello,
I recently tested the nRF51822 with a non-Nordic BLE devices and encountered some problems. When testing with Nordic the connection is maintained with no problem...
During testing I changed the device name in the DFU. After making the change the DFU client in the master control panel would no longer work.
Is it possible to make the...
HI,
I want to use PWM to control various hardware (LED's, etc ..) so I started off from the suggested PWM code example, found in this forum + modified it as I want to use...
Hi
I try to configure a ppi channel with timers to generate pwm signal
My entire code is working well without softdevice.
Here my ppi init function:
NRF_PPI->CH[0...
I am planning to build mobile devices that communicate directly between them with BLE. The devices are all the same and carried by users. users meet and exchange data. I can...
hi,all!
i am confused about whicn priority should i set for my interrupt.
For deteils, I need a gpioe interrupt for my button, and this button is used to POWER OFF my...
We wish to make a universal device that may used
for ANT with the nrf51422 and the 32kHz crystal.
or for BLE with the nrf51822 without the 32kHz crystal.
Will there be...
I'm trying to bring up a basic S120 application on PCA10001 based on the multilink central example, using the IAR toolchain.
I've programmed the S120 device using 1.0.0_3...
I'm developing a next generation device using nrf51822. To replicate existing behavior I'm trying to sniff the previous generation product behavior using the ble sniffer on...
Hello!
I am working with a NRF51822 and I need to change the address of pipes regularly (so I can use more than 8 NRF communicating together with ESB protocol).
My problem...
