Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
Hi,
I have a custom board, i enable the adc peripheral, and it generates:
then i connect the AIN4 channel and it generates:
but when i build i get the following...
Hi, I'm looking to develop an out-of-tree driver for the SIM800L modem. The reason I want to develop it out of tree is that I don't believe have the skills or resources to...
HI
I previously disabled DCDC in the app using the following method:
in app.overlay
I am using ncs 2.9.0 I saw some posts using CONFIG_ENABLE_DC_DC=n , but I am unable...
Hi,
I'm try to set up a UDP server on a nRF9151dk, and send data from a remote pc to the devkit. I have tested my sim and networking works correctly, I am able to use coap_client...
Hi,
I am using the nPM1100 in my new application, where the system power circuit includes two additional 250mA LDOs configured to provide a 3.3V output . I am also using...
Hi,
I am encountering the following build error with the BLE peripheral example after migrating from NCS 2.7.0 to 2.9.0 and when CONFIG_BT_LL_SW_SPLIT=y is set in prj.conf...
Hi,
I am using nrf Connected SDK v2.6.2 on windows 10. I try to create a blank application project for the device ADXL363 on SPI2 bus on the nRF9160DK board.
I basically...
hi:
I use ncs 2.8.0 ,nrf9151 dk and v2.8.0\nrf\samples\net\https_client.
I modified the DigiCertGlobalG2.pem
this is log:
connect() failed, err: 111.
What is the...
Hello,
I was wondering if there was a way to implement a physical on/off switch to the npm1300 that would allow the outputs to be isolated form the battery but still having...
We have designed a vehicle tracker that uses the NRF9160. We have found in the past that sometimes after the radio has been running for a while it gets into a loop where it...
Hi,
I try to develop a Bluetooth speaker using the nRF 5340 DK since i do not have a separate audio Dk for this. I am using the sample code Audio unicast client for this...
Hi
I have a project developed on the nrf52840dk / nrf52840 dongle and am trying to build it for the Laird BL654 dongle. The build fails due to a missing 'runners.yaml' file...
When I get a custom board, how do I detect and flash it? I have three options on the board:
I have a USB cable with:
GND
D+
D-
+5V
OR can configure the usb...
Hello, I'm trying to get nrf5340_audio example running on nrf5340 audio dk.
I'm able to build the code and run it however i'm unable to bond with my mobile phone with android...
Hi! In order to get more accurate battery SOC measurements I need to provide a custom battery model to the app. So, I had to use the nPM1300 EK + Fuel Gauge board to profile...
