nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
1. What is the Bluetooth version in NCS 2.6.1?
2. How to get Bluetooth version from NCS? is there any variable? I cannot find it in the release note neither. https://docs...
Hello,
I am using nRF Connect SDK v2.9.0, and nRF54l15 board. I enabled the watchdog timer and used its driver in zephyr/drivers/watchdog.h
It seems to work fine. The...
I have checked the PWM library in the nRF Connect SDK, and it seems that the library does not support init and deinit functions. The function pwm_set_pulse_dt(&pwm_led, 0...
Hello,
I’m currently working with a custom board based on the nRF9160 SiP, and I would like to measure the LTE-M TX power after the antenna impedance matching circuit. Ideally...
I am using the nrf52840 chip on a custom made PCB that is powered by a USB-C which provides it with 5V.This 5V is then converted to 12V using CH224K which then is wired to...
Hi,
we have ESB PTX and PRX couple from nRF54H20 nRF54H20DK (rev. 0.9.1), SDK: v2.9.0-nRF54H20-rc2 and the same Toolchain, IDE: VSCode + nRF Connect plugin build for CPURAD...
Using wireless sensors with nRF54L15, the sensors do not need to be connected, only broadcast a small amount of information. There will be 50-60 thousand nodes, and they are...
Hi, I'm trying to setup serial recovery in my project, in order to update firmware via USB cdc-acm.
I'm following this exercise from the academy which seems what I need...
Hi. I can't build the hello_dect example using cmake, the build process is failed with the following error: In file included from /home/cybermag/ncs/nrf/modules/trusted-firmware...
Hello!
I am interested in the Non-IP Data Delivery support in the nRF9160 module. In the description of AT commands, I did not see an opportunity to set PDP-type="Non-IP...
We use a module like EC2832AA1. I checked that nRF52832-QFAA-R is used for this module. This module has ap-protect enabled. So I added the command "nrfjprog --recover" to...
Hello!
We have developed a product that we would like to add some testing for and I have looked at both ztest and unity testing. Currently I am struggling with running the...
I have tried using SMP svr example with MCUboot for FOTA, NRF Connect SDK version 2.9.0. The example is located in zephyr\samples\subsys\mgmt\mcumgr. This example is working...
Hi, I have develop a project nRF5340 + W5500 Ethernet IC
Last time I develop a code with nRF52840 + w5500 and work success, but this time the same code work with nRF5340...
