Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hello All,
I'm trying to build a receiving unit using the nRF24L01+ and PIC16F628A. Im using an nRF24L01+ and RaspberryPi as my TX unit which i managed to get working ...
Hi,
We have a device using the S110 v6.0.0 softdevice and the SDK v5.2.0.
We started working from the Proximity application available in the sdk.
Is it possible to...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I am trying to use the ADC to take power measurements on an interval. I found an example to read the values out online:
void ADC_IRQHandler() { nrf_adc_conversion_event_clean...
I am designing a PCB using the NRF52832 and this antenna . The antenna design guidelines suggest ground clearance and direct traces from the NRF52832 to the antenna without...
I am working on a project which I wish to Paer between to nRF51422 devices and to use the auto reconnect between them. there won't be any display so it must be automatically...
Hi,
is it necessary to use internal regulator for NFC DC/DC or we can use normal internal LDO in design.
also if we need to use internal DC/DC regulator, what is the...
Hi, I have tried to find a solution for some time now in the Nordic Semiconductor forms.
We have been noticing a peak or a disturbance in voltage in every connection interval...
I have encountered a scenario in which my application is terminating the BLE connection via a call to sd_ble_gap_disconnect, while around the same time I receive a write request...
I'm able to successfully use peripheral/uart example to read the data from GPS module. I achieved the same by setting baud rate to 4800, and connecting rx and tx of GPS to...
Hi,
Question about FOTA (firmaware upgrade over the air).
I know that nrf52832 has 512 kB of flash, and the ble stack( softdevice ) has 136 kB , and the bootloader has...
Hi,
I put my NRF52 to sleep (POWER OFF mode) and configure it to wake on GPIO port event like so:
This GPIO is set up on a reed switch. Occasionally, the NRF52 will...
Hi
I found a strange issue on nrf52832. And I use nRF5-SDK-v13.1.0 .
When I assignment P0.7->SCL & P0.6->SDA, the twi function not working. But I change the assignment...
Today I read about the new nrf52810 and I want to know about its main differences with the nrf52832.
I see a lower power consumption for the 52810 vs 52832 and no NFC on...
Hi
Currently I try to migrate my software project (with SDK14.2, S132 (5.0.0), arm-gcc toolchain ) from nRF52832 to nRF52810 (with SDK14.2, S112 (5.1.0), arm-gcc toolchain...
Hello everyone, I am a beginner in the use of Nordic Thingy: 52. I would like some help trying to reprogram the Nordic Thingy module. After a programming error of the Thingy...
HI,
I am unable to communicate between a SDK 8.0 based nRF51822 sender and SDK 14 based NRF52832 receiver.
The data rate of the SDK 8.0 sender is 250 KBits/sec, whereas...
Hi,
Can someone help me with question on SPI?
What is the difference between SPIM and SPI? They seem to have different clocks
Also in the SPIM section, the frequency...
