Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
Hello,
I am designing a custom board with NRF52832 IC. I followed the same layout design as suggested by Nordic.
But , I made some additions to reference layout. I added...
I'm trying to set up a gazell device with a channel table that is 16 channels long. This is for a pairing application where the host has a channel table that is 6 channels...
I'm using SDK13.0.0 ble_app_ancs_c example.
On connected with a phone, pm_evt_handler is called with PM_EVT_CONN_SEC_SUCCEEDED, and call ble_db_discovery_start(), then...
hi,
i want to make BLE central node with Nrf52840 for receiving multiple data from Nordic thingy 52,i am using keil IDE with Nordic sdk 14.2.0 and blinkey central(s140_PCA10056...
Is this possible to change MTU Size in nrf51822 Board from 23 to 43?
is any changes is done android side app? the application is same copy of nrf Toolbox UART app.
please...
Hi, everyone,
I am developing the project on nRF518522 and I must use the flash memory to save the data. The data must be saved while the device is conncted via BT with...
hi,
When using the UART examples I found that as long as I opened the uart_init () program will not work, debug the discovery process will be executed
case APP_UART_COMMUNICATION_ERROR...
Hi,
I am trying to develop an application which recieves data over SPI and I want to send this data over ble, I am using NUS service. I am recieving 5 bytes over SPI at...
Hello,
I'm using 2 nRF58840 dev kit with SDK 14.2.0.
I'm trying to read the RSSI value of the second board from the first board using LE Coded PHY in both modules.
...
Hi every body , i have some issue if you don't mind. i rooted a board with NRF52832 SOC without PCA. i want to get a uart connection with pin 8 and 10 . It s possible to do...
Hi,
I am wondering if its possible to download a fds record on android device when connected ?
I want to save data and retrieve it when I get connected to it.
Th...
hi team, i want to edit my uuid, major and minor. i searching for the example. i am using nrf52840. i didnt get any example. but there is a example for nrf51 ble_app_beacon_bcs...
infocenter.nordicsemi.com/.../nwp_015.pdf
Above refered white paper says:
"refer to the Nordic Semiconductor white paper ‘nRF TX measurements’ for procedures on how to...
Is it possible to set two nRF52 as duplex MODEM?
The objective is to monitor a remote solar powered device from a PC. There would be one nRF52 device at each end (one at...
