the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hi all.
Consumption current increases by about 1.5 mA after a battery check.
uint8_t battery_start(void)
{
// Configure ADC
NRF_ADC->INTENSET = ADC_INTENSET_END_Msk;...
Hi all!
My project is depend on the "ble_app_template",which uses the "scheld structure", I am able to read the data from app but not able to send my data with notification...
I have a question about that code, when I test my code with lightblue, it showed me that there is an service called application notification client service, but it didn't...
I'm using GPIOTE library to check the change of two switch inputs.
Normally it works well, but rarely GPIOTE_IRQHandler become never happen even if the pin level changes...
Hi Nordics!
I am using app_pwm.c file in SDK 8.1, and when I use it with softdevice(advertising or data transfer event), sometimes pwm signal is reversed.
I guess, reversed...
Hi Guys,
I am using a the 350Mhz Analog Oscilloscope HM303-6 www.hameg.com/hm303-6.0.html to measure the voltage utilised by the board when it is transmitting data.
...
Hi,
Once I enter into BLE mode I am not able to read any gpios(nrf_gpio_pin_read) also I am not able to set any gpios (nrf_gpio_pin_set).
Below is my example
uint8_t...
I'm trying to establish a bond in my project and then perform service discovery, however the discovery is returning the BUSY error.
I tried to wait for the events according...
In SDK 8.0 the bare word asm was re-introduced in nrf_delay.h , causing failures in compilations that use strict C/C++ standard conformance flags. This was noted in earlier...
Hello Developers
I have to solve a problem for which I could not find much information about online, so I am hoping you guys can help me.
I am developing a WIN32 application...
Hello, For some reason the Ble App Uart is not working on my PC anymore. I have gone over Nordic tutorial again however, the LED doesnt blink and I cant detec the device on...
Hi,
What are the general causes of SDS assert in nrf51/52 ? Assuming that SW has been tested, is there something that could happen in the code that would cause the assertion...
Hi All,
I'm using "scanForPeripheralsWithServices" of iOS to the BLE devices.
"scanForPeripheralsWithServices" sometimes never return anything.
I have to stop scan or...
Hello! I'm trying to build a program for nrf51822 via QT Creator.
I'm using QBS for build. I have a makefile from SDK examples for nrf51822. Someone can help me, how to setup...
Hi all,
I have the exact issue mentioned here - github.com/.../9
I have updated my makefile to generate only one bin file from the Softdevice Hex file, but still I'm getting...
