Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
Along with S110 BLE stack I programmed my application, which I managed to do without any conflict.
My application is not working properly and neither control is transfered...
how much time of keep level HIGH/LOW can make nRF51822 detected the HIGH/LOW level and generate an interrupt?
how width of impulse need to generate an interrupt?
Hi Team,
I was trying to load firmware to external board using nRF51-DK.
I have successfully programmed the boards many times and now when I am trying, LED (LD5) on nRF...
Hi all,
I downloaded the nrf51SDK_.8.0.0 from nordic site and tried to flash the new softdevice s110 but failed. I used an android application to flash it over the air...
Hi:
i use ble_app_uart project and want to change the UUID lenth(128 bit) to be 32 bit;but i change "nus_base_uuid" to be 4 byte and change "uuid128[16]" to be "uuid128[4...
Hi,
Does hardware that has already a Qualified design Listing (Bluetooth.org) requires re-testing of the RF-PHY ?
(refering to transmitter tests (i.e TRM-LE/CA/01/C (output...
Hi,
Im using a module NRF24L01 + LNA bought off ebay, connected it to msp430 via SPI interface. All spi communications are going solid, I manage to completely configure module...
I am trying to create a file and write to it during runtime. When I use fopen with "w" option to create a new file, the file pointer is always retuned to be NULL.
Is there...
Hi,
I recently tried SDK7.2 on PCA10028 board in order to make sure that SDK7.2 works well before I migrate my project to SDK7.2 codebase. My project code didn't work as...
Is it possible to do OTA from one nRF51822 to another? Is so how, and is not why?
I am using S120 and S130 for my applications and would like one device to uppgrade another...
Nordic has provided a good SPP implementation over BLE.
devzone.nordicsemi.com/.../
However, will it raise power consumption and cause BLE to lose its low-power characteristics...
When trying to do a direct advertise massage ( sd_ble_gap_adv_start ) I get error code NRF_ERROR_INVALID_STATE (Invalid state, operation disallowed in this state). This is...
Hi Team,
In my application UART is used.
I need to send parity bit based on particular responses that I need to send to the device
connected to UART.
Can I change configuration...
Hello,
I'm working with timeslot API (basing on github.com/.../observer) . I have an advertising and active scanning running concurrently. However, I want to completly...
