Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hello,
In an application with the nRF52832, Softdevice and SDK 17.1.0 I try to use the temperature sensor according to the peripheral example. I attach the temperature.c...
Hi,
when I have the nRF Connect for VS Code Extension Pack installed locally it will break Dev Containers. The following error message will be shown when I try to run...
Hello everyone,
I'm trying to use the buttonless dfu functionality on nRF52 DK. However, I can't seem to test the functionality when there is no bootloader flashed, but...
Dear sir/madam
I'm designing the custom PCB for bluetooth application. I have some doubt on 50 ohm RF line. How to maintain that 50 ohm in track.
Kindly support regarding...
Hi, I have followed the nRF Connect SDK Fundamentals and BLE Fundamental courses and come to Lesson 6 Bluetooth LE sniffer. Everything has worked until this but now I get...
Hi,
In nRF52811-CAA chip, which pins are allocated to ADC inputs. In Table 122 of datasheet which shows pinout for WLCSP package, it just mentions AIN1, AIN2, and AIN3....
Hi,
I am facing an issue while flashing the code using an external debugger. I want to flash an LED blink code on the I/O shield " Raytac MDBT53V-P1M. " For this, I am using...
Latest 2.7.0 toolchain.
nrf5340DK board, light_bulb example.
I am using our own smartphone to perform up to AddNOC and ThreadNetworkSetup.
Then the control is transferred...
Hi, I would like to write a log to an SD card but I am completely unable to even connect to it using SPI in Zephyr/nRF Connect SDK. There seems to be some mismatch between...
I am working in NCS v2.7.0 for nRF52833 DevKits, and trying to set up a secure BLE connection to allow remote control of the device over GATT.
My devices are headless IOT...
Hi All, I have a 5340dk and it got bricked for no reason, last night I was able to flash and debug my program. But when I tried this morning, device is behaving unexpectedly...
Hello !
You have DTM test in nRF5_SDK_17.1.0 and in nRF Connect SDK.
I have used SDK test some years ago and it looks more simple if we compare it with new environment...
Hello,
I am working with the nRF9160 to communicate via DTLS. It works, but managing certificates is a bit of a problem. I am using the AT%CMNG command.
First, certificates...
