Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hello,when i get connected to the phone,when i call err_code = ble_hts_measurement_send(&m_hts, &simulated_meas) and err_code = ble_bas_battery_level_update(&m_bas, battery_level...
I got the Dynastream N5 kit and have successfully used it with limited ANT work and was trying to get BLE working but can't get a driver for the USB dongle. On the 51422 product...
Hi All,
I am working in the sleep mode with system off and wake up with internal RC clock.
It function well when connected to EV board...
I see the "Emulated System...
Hello, I have an eval board of " nPM1100-EK -> PCA10123 0.8.0 " battery of li-po 3.7v 600mah battery termination voltage is 4.2V The above eval board works fine & the battery...
Greetings,
I'm trying to migrate the MAKEFILE configuration to SEGGER studio so that I could build and debug the project from there. So far, I'm stuck on the Linking part...
We are currently working on a Zigbee-based network coordinator using the nRF52840. I have a function, dfu_multi_image_write , that writes data to NVS in chunks. The function...
The Power Profiler app v4.2.0 release notes say:
"Updated PPK2 firmware to v1.2.0, which adds COM port for shell access"
Are there any instructions available how to use...
Hi,
My application is running NCS v2.5.3 on a nRF5340.
My project has FOTA via BLE, is running mcuboot, and is a multi-image build. I am trying to verify, from within...
Hello, I am trying to subscribe on a topic to get retained message.
I am using ncs 2.7.0
The problem is that whenever I am trying to subscribe to a certain topic, I have...
Dear all,
For a project we need to synchronize up to 5 data loggers, each of them is based on nRF52840. The sampling rate of some sensors can be of 1 kHz. I'm wondering...
Hi All,
I am lookging for a way to use the nRF7002 (or other 2.4 GHZ WifI solution) as a WiFi sniffer.
I want the solution to provide, for each WiFi packets in the previously...
my nRF52840 has MBR, SoftDevice, Application and Bootloader.
Can Bootloader call API in SD?
Will it be an issue? If I need to upgrade SD (could be a newer version),...
Hi there,
In Zephyr 3.6.99 I see a promisive function to make sure that the logging buffer is flushed at a certain moment of time: log_output_flush . It is using a pointer...
I am trying to use the following example, hci_pwr_ctrl . I have tried using the example just as it is but i keep getting errors when trying to build as can be seen in the...
I have a custom board with an I2C connected sensor ADXL345. I have to do GPI/O initialization to select the I2C. This works because I can read the ADXL with custom I2C commands...
Hi
I am using nrf52840 in my custom board. I have a gpio button which is assigned for as a factory reset button. So when i press the button the whole board needs toi be...
Hello,
we are looking to develop multiple BLE audio source which sends the mic data to the receiver and the receiver receive the audio data from multiple transmitters...
