Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Is possible to use ble stack for the configuration and disgnostic of a device and that use ieee802154 to make a start network for 1 to 8 devices , where i can find an examples...
I couldn't find anything related to this issue on the devzone, so I hope this can help someone who has the same issue:
We're using the NRF54L15 QFN52 variant with a custom...
Hello,
Setup
MCU : nRF52840
SDK : nRF5 17.1.0
Transport : Secure Bootloader (UART)
No SoftDevice
Custom HW
The Problem: I am experiencing two conflicting...
I have an application running on a custom board using the nRF52840 that uses the SAADC. After migrating my nRF Connect version from 2.6.2 to 3.1.1 the current draw of my battery...
Hello,
I've been having problems in getting the correct battery voltage for a Thingy53 for a number of projects, when using the latest nRF Connect SDK 3.2.1 (Zephyr 4.2...
I am trying to develop a BLE HID peripheral that can be used on Ubuntu 24.04.
When I try to connect the peripheral_hids_mouse example to a Linux machine, it immediately...
I have two problems. This is the first problem.
[Environ]
nRF Connect SDK v3.2.1 nRF9151 (Custom board) VSCode (1.109.4)
The first problem is that debugging doesn't...
Hello,
You've previously provided the sourcecode for nrfutil, before it was rewritten here https://github.com/NordicSemiconductor/pc-nrfutil .
Is it possible you could...
I am developing a FW for the nrf54l15 which should log sensor data into its internal flash (RRAM) and make it read able later from a Smartphone via BLE.
For this scenario...
Hello everyone,
We hope this message finds you well. We'd really appreciate some guidance on an issue we've been encountering in the field.
We have deployed several hundred...
I am dealing with a HardFault occuring in my code, and I am unable to trace the error. The output when the HardFault occurs is <error> hardfault: HARD FAULT at 0xD0D0D02A...
Hello,
I am using the Nordic Thingy:53 and trying to collect sensor data using Edge Impulse.
I was able to successfully connect the Thingy:53 to Edge Impulse and stream...
The device i am currently developing is a battery powered dongle with internal power supply unit for battery charging. I am using nrf5340 USB pins D+ and D- for communication...
HI, i have been using the nrf9151 to download my OTA's it has been working fine, but since this week it stopped working for all device we have deployed, i suspect it is related...
Hi ... have code that outputs I2S in master mode. The slave, a NAU8822 device requires Master Clock Source between 8 and 33MHz.
The 54L MCLK pin is duplicating the BCLK...
