Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi,
I made a custom board with nRF54L15. I do not have a spectrum analyzer, so I cannot tune how much power goes to the antenna or how much is radiated. So, I started ADV...
We need to measure the RF power(continuous unmodulated signal) of our custom board based on nrf5340 using spectrum analyzer. please suggest the steps and tools to perform...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Good afternoon,
I'm trying to test PCA10001 eval board power consumption and consumption is about 4mA when it should be considerably lower.
To proceed with this measurement...
Hello !
When i was trying to configur my SPI, I observed that there is a difference between the position field announced in the nrf51 reference manual v2.1 and the nRF51_bitfields...
We are looking for the sample software for transmission of nRF2726 (nRF24Lu1P).
nRF2726 does not carry out transmitting operation in enhanced_shockburst_ptx_nrf24lu1p.uvproj...
What I've been observing here is a curious issue under some very specific circumstances. First off, I am using a Xuntong Tech PTR9018 module (this is QFAAC0), the S120 1.0...
Hello all
I making some device with ARM core CPU with nRF51822.
I set CPU to SPI master and set nRF51822 to slave.
And then I read some data from nRF51822, that was...
I am Merging 3 firmware s110_nrf51822_7.0.0_softdevice.hex, ble_app_beacon.hex and bootloader.hex to Output1.hex as follows.
mergehex -m s110_nrf51822_7.0.0_softdevice...
I'm trying to use the Bond ACI command on my nRF8001, but I'm having trouble using it as per the datasheet.
When I set the Timeout parameter to more than 30 (0x001E), the...
The documentation for the nRF51 says only code from code region 0 can execute the erase and write command on code inside code region 0. This means that my bootloader in code...
I flashed S110 softdevice and ble_app_hrs application to nRF51822 on PCA10005 with nRF6310.
and then I tested by nRF toolbox on iPhone5s.
But ble_app_hrs application seems...
I'm attempting to implement a buffer in flash using the persistent storage module but have hit a bit of a wall. When I manually set the block size to something less than the...
Hi,
i'm developing an app for Android and iOS that needs to comunicate with a devices based on nRF51422 with S110 v7 loaded.
We want to encrpyt all comunication and enstablish...
Hello All,
I would like to implement static pin on my sensor. Remember how some Bluetooth Headsets are hardcoded to '0000' I would like to implement '123456' since BLE...
Hello all,
I am using nRFgo motherboard(nRF6310) and nRF51422 DK(s310) and
MDK_ARM(keil Version 5 IDE) to build the sample code.
It seems workable to program and download...
I just got an mBed board and I'm having trouble getting the J-Link to work on OS X even though I have version 4.90.
MattBookPro:gcc mbrandt$ JLinkExe
SEGGER J-Link...
