Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Dear sirs,
My purpose is to transmit stereo HiFiaudio from one source to two speakers wirelessly.
The speakers have their own power amplifier.
The problem is that the...
I am trying to build PCA10040 examples but I am getting the following error:
make genhex
Preparing: .hex
/home/me/nrf52/gcc/gcc-arm-none-eabi-4_9-2015q1/bin/arm-none...
Hi guys
I am planning to develop a beacon app, but I am not sure what would be the minimum scanning interval in order to keep the phone's battery drain on a fairly good...
Hi, I use the following.
Raspberry Pi 3 (RPi3 with Raspbian Jessie 4.4) as a router,
RPi3 is connected to a Wi-Fi router to access the Internet by using the built...
Hi, there! nRf Toolbox drove me crazy!! can anyone help me?
I flash "s130_nrf51_2.0.0_softdevice.hex" to the pca10028 board.
I compile the bootloader example "nRF5_SDK_11...
Hi,
I'am having an issue with UART using app_uart_fifo.c (SDK 0.9.2). At times I get communication error (usually at attaching and detaching uart connector) and my error...
Hi.
I'm little worried about our bt sensor power consumption.
We are using twi/i2c to communicate with sensors periodically. We are using app timer to trigger these...
I have a custom board that doesn't use the external 32Khz crystal. The engineer that designed it chose to use P0.0 as UART RX. (I know, poor choice.) I have set up a custom_board...
I am using SDK_11 s130. I see APP_ERROR_CHECK(err_code) being used throughout the SDK examples. When err_code is any value other than NRF_SUCCESS, the nRF51-dk board will...
Previously, I was able to program ble_app_uart using SDK_11 s130 into nRF51-dk. Now, I would like to program ble_app_uart into Adafruit Bluefruit LE friend board. www.adafruit...
I have been following the advertising tutorial and decided to start my own application using nordics git repo as a reference. After a few debug sessions I found that I needed...
I am trying to probe sysclk signal on one of the unused GPIO pins on a nRF52 board. I modified the ble_app_template example provided in SDK 11.0.0 and added a sysclk function...
I am trying to connect nRF52 with 7120 and create a NFC card reader , is this a solution and power efficient solution .
I will interface through I2C , is there a example...
I am using the sdk version 11 and arm-none-eabi-gcc version 5.4 on linux mint to compile the blinky test application. I have pointed the Makefile-posix at the location of...
I am doing the test about timeslot with the project link text
but it cannot scaninng and i found the timeslot is work because i get event NRF_EVT_RADIO_BLOCKED and it call...
