Hi,
We need to write binary content from a binary file (.hex or .bin) to a specific area of the external flash (QSPI).
According to this topic: , this is similar to our...
Using nrf sample from v2.9.1/nrf/samples/crpyto/rng Configure build with v2.9.1 SDK/Toolchain Configure build with board target: nrf5340dk/nrf5340/cpuapp Add MCUBOOT support...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hello,
I am currently using nordic connect sdk version v3.0.2 which seems to be the latest release on github. I am using https client example. As per the requirements...
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
I am trying the ANT-OTA DFU Update using two nr51422 pca 10028 board. One is sending Transmission messages in the CHANNEL_TYPE_MASTER mode, while the other is receiving Messages...
Hello, I'm a beginner for nRF51822, now my status is sticking on those SDK_11.0.0 BLE examples, while I could successfully running non-BLE (such as examples of bsp/uart)....
ElfApp.zip This attached application is based on Nrf_uart demo app.
It works fine under Android 5.0 and 4.4 smartphone. When I click the connect button, it shows the info...
Hi,
I'm on the project where I use SoftDevice s132 on my own devBoard with nrf52 chip.
I know for Connection Interval and other parameters that determin BLE communication...
I am using nrf51822 as a central device that is trying to connect a peripheral device nrf8001.
I want to build communication bewteen them and use nrf51822 to receive the...
Hi,
I have a small question regarding flash write/erase cycles and I was unable to find a clear answer.
I can see in NRF52 specs:
Flash write/erase cycles: 10...
Hi,
I've been trying to get DFU updates working on my device for a while now... I've got the single-bank bootloader compiled and seemingly working (and a combined hex file...
how to modify ble hand shake time which normal connect to phone.
this scene the ble board has connect to the phone, but need down scoping the ble time to let the 2.4G work...
Hi,
I would like to save some data from characteristic into the Flash. Due to this fact I decided that I will use scheduler. When the value of actual characteristic is...
We are trying to complete Bluetooth qualification on our Cycling Power Service (CPS)
against the Bluetooth Test Specification (Document Number CPS.TS.1.1.0).
We fail the...
Apparently, the dfu bootloader example in nrf51 SDK 8.1 is not working on PCA10031 type(16K RAM devices). In my case, the device is RedBearLab BLE Nano and nrf51822.
Can...
Hello,
because of my mistake, rx tx pin was not cross connected.
So i want to swap rx tx pin on nrf51822.
In the example ble_app_uart_s130_pca10028, i change the code...
