در دنیای پررقابت صنعت غذا، موفقیت رستورانها، هتلها، تالارها و آشپزخانههای مرکزی وابستگی زیادی به کیفیت و کارایی تجهیزات آشپزخانه صنعتی دارد. برخلاف آشپزخانههای خانگی،...
I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
Hello everyone,
I’m working on a project using two nRF5340-DK boards to measure throughput and RSSI while dynamically changing the PHY and TX power. I started from the official...
Hi,
When i want to connect my Power profiler kit II to my laptop, it first blinks GREEN. After i connect to it using the power profiler app, it goes: RED -> AMP (Ampere...
I have a custom board with a nRF5340 and need to configure VREGH in DC-DC mode and set 3.0V output on it.
I see the documentation on REGULATORS — Regulator control where...
Hi all,
I've been trying to develope a project by using an nRF51822 chip. The project is about to finish. However, I couldn't implement the pstorage module in a correct way...
I am looking to re-install the firmware on my dongle after making it a sniffer but I can't find a hex file for PCA10031. My MasterControlPanel has firmware for PCA10000 should...
Hi
Should I get a characteristic write event ( BLE_GATTS_EVT_WRITE ) with s110 as well with the
following property configuration:
char_md.char_props.write = 0;
char_md...
I try to achieve something similar to IBeacon where data is pushed to any device listening, but where the data is changing over time. Is it possible to (frequently) change...
Hello,
I have recently had to install the nrf tools on a mac computer. The tools have been recently ported to macs, but unfortunately I am getting the following message...
Greetings,
During a connection between two nrf51422s running on S120 (2.1.0) and S110 (8.0.0) with a connection interval of 7.5 ms I get only a maximum RSSI of -42 dBm...
Hello,
I developed a firmware on nrf51422 with nrf51. I use a development board PCA10028.
With this firmware I control the directly the radio registers (Soft Device is...
I have a nRF51822-EK evaluation kit (so, PCA10001) and am trying to get DFU working with an S120 SoftDevice as per the answer posted here:
devzone.nordicsemi.com/.../ ...
nRF51822
I'm interested in setting up the the POFCON to enable me to get a
POFWARN interrupt when the battery voltage drops below 2.7V.
The softdevice is enabled at...
I have a nRF51422 dongle, and I want to know the power/current when an UART event happens.
I've read nRF51822_Development_Kit_User_Guide_v1.4 p.29 for Current Measurements...
Hello,
I am experiencing some CC register issue in Timer of nRF51822. I am trying to setup TIMER1 for 16 seconds. But I see, that when I try to write to CC registers, the...
The "Intermediate Temperature" characteristic is not coded in the ble_hts.c file.
How could I do to implement this characteristic and maintain the compliance with Nordic...
Hello,
I want to rewritte SEGGER_RTT_vprintf to use sprintf Inside (because it's already linked in my application and allow float display).
The problem is that i don...
