Hi Nordic team,
I tried to view logs from my custom nRF54L15-based MCU using J-Link RTT Viewer, but it's (printk) not working. The same prj.conf configuration was previously...
Hello Nordic Support Team,
I am working on an nRF52-based project on a custom PCB using the E73-2G4M08S1C devboard ( https://www.cdebyte.com/products/E73-2G4M08S1C ).
...
NRF52840
S140
APP based on ble_app_multilink_central
1 PCA10056 as central, 1 PCA10056 as peripheral, the cantral can find the peripheral and buid connection.
But...
I had the nrf5340 DK working for a few weeks now, and while working with SSD1309 OLED peripheral, was trying out a simple display application. Couldn't get the display device...
Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
در دنیای پررقابت صنعت غذا، موفقیت رستورانها، هتلها، تالارها و آشپزخانههای مرکزی وابستگی زیادی به کیفیت و کارایی تجهیزات آشپزخانه صنعتی دارد. برخلاف آشپزخانههای خانگی،...
I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
In previous SDK (or softdevice?) version, the maximum data length for a notification was 20 bytes .
With SDK V10 and softdevice 8, the following code returns error NRF_ERROR_DATA_SIZE...
Hi, I have implemented a music control button.
This button can send (volume+, volume-, play music, stop music and my custom control (0x06) for my app ).
Procedure:
...
Hi, im trying to update the firmware of a nrf52 using dfu ble. For example, have a blinky example running and switch to a blinky2. Can anyone know if this is possible?
Hello,
I am doing a search in the Eclipse to find texts, I noticed that Eclipse is not finding any of the texts from the Include files. I did a google search on this issue...
Hi,
I use pstorage to allocate 32bytes of memory with 2 block, means each block having 16 bytes, when I write 16byte data into block_0 portion, I am not able to go to the...
Hello,
I use the Segger J-link software with my PCA10001 and recently updated it to last version (v.5.1). After install it asked me to update the firmware to the last version...
Hello,
I'm trying to flash external nrf51422 module.
I want to flash both softdevice and application. I used below commands:
mergehex -m %SOFTDEVICE_NAME% %APP_NAME...
I want as much control over advertising as possible. Barring that, I want to understand why the softdevice automatically goes back into advertising after a GAP disconnect...
Hi,
Assume that we want to send a data array by putting it in consecutive advertisement packets. I know that data update has to be done by calling ble_advdata_set(...)...
Hi
I'm trying to implement battery level on my custom profile.
So I used battery.c and ble_bas.c files for the battery service from nodic's sdk nrf51822_v4.4.1.31827....
I have make over your bootloader example to create my own without BLE support in bootloader (new programs are send in application instead of in dfu bootloader). Bootloader...
Having some trouble using the NRF52 as RX and nrf24l01+ as TX. The NRF52 receives the packet, but for some reason it always says CRCerror.
Anyone ever tried to use NRF52...
