I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Hi, i am using:
-nRF 52 DK
-nRF 52832
-Sensor of Maxim Integrated
-SDK 17.0.2
I have some problems in handling the I2C through the nrfx module.
This is my ReadByte...
Hi, I have a set up consing of an nrf52840, a Raspberry pi and a Linux workstation, which communicate over IPSP following the IPSP sample from Zephyr OS. The nrf52840 is a...
Hi All,
The nRF54l15 datasheet (v0.8) notes in section 8.25.12 under "Configuration" that UARTE20 can use dedicated pins on P2, but there is no clarification that I can...
Hi,
It feels like i have a follow up question of my ticket here .
We are currently developing a product using the nrf54l15 using the nrf connect SDK v2.9.1 with the toolchain...
I'm in the process of upgrading one of our applications from NCS 2.6.1 to 3.0.1. According to this document, the only versions of NCS that support modem firmware 2.0.1 and...
Hi all,
We are running v2.4.0 SLM in nRF-9160 as pure modem, communicating with our external MCU. And we need to send a MODBUS-TCP write request command about each 10 seconds...
Hello,
I am testing the RF range of a BLE application based on PAwR (Periodic Advertsing with response) in coded PHY (S8) with SDK 2.9.0.
In order to test the robustness...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
There are two USB ports. IMCU and nrf5340. I had a lot of trouble with bad cables but i found one that works and I find that I have a jlink drive that pops up so I know there...
Hi,
I want to port an exisiting solution from ESP32 + nrf24 to nrf54L15. I didn't find any example that would work out of the box for my POC which would to combine very...
Draft — ready to post on Nordic DevZone / Zephyr mailing-list
Title nRF5340 DK + MCP2515/TJA1050 module — can_start() always returns -EIO even in loop-back
Hardware...
Dear Nordic Support Team,
We have a system where an MCU is connected to a Wi-Fi module operating in NCP (Network Co-Processor) mode . The MCU controls the Wi-Fi chip to...
Dear sir,
I'm using the sample application "channel_sounding_ras_initiator" to performing the evaluation. Here are my test environment: - Developement kit: nRF45L151 - Tool...
Hi,
I'm using the nRF52832. And I was wondering if it really does support LLPM. I found sources that clearly state tat it does (e.g. the wireless mouse/keyboard example...
Hey, I have a problem understanding BLE behavior
I had a product was running in BLE phy 1M, and I wanted to convert it into PHY CODED.
It just sniffs all the advertisement...
I attempted to use nRF52840 for multi-connection data interaction, but whenever I was debugging, I always encountered the problem of being unable to establish a connection...
