Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi all,
I am making a device which involves using nfr52832(PCA10040) to communicate with a NAND flash through spi to store data acquired from the ADC. After all the data...
Hi everyone,
We’re currently using the nRF9160 module with JIO Nb-IoT SIMs in our devices. Could anyone clarify if any specific actions are needed in the firmware for...
Hello, I know it's a bit basic, but running through all the docs for thingy91:x I got a bit lost.
https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/app_dev/device_guides...
Hi,
I am encountering an issue with the TWIM driver when attempting to communicate with the nPM1300 PMIC via I2C.
This problem seems to be related to the behavior of the...
Using NCS 3.0.0
When placing the app slot 1 in external flash, mcuboot cannot open the flash area.
I am testing this with nrf54L15 + 8 MB SPI flash on the DVK.
This...
Bluetooth connection cache processing - Nordic Q&A - Nordic DevZone - Nordic DevZone
Continuing from last time. After some optimization, the program was able to work. However...
Hi, I was using the BLE online power profiler to determine possible power savings with the nRF54L15DK over the nRF52840 using the zephyr bluetooth broadcaster sample. The...
Hi.
I'm using nrf Connect SDK v3.0.1 and Zephyr v4.0.99 to implement a IoT device which connects to a Thingsboard server with CoAP. With the COAP_CLIENT Lib I want to download...
I have created a custom board with an NRF52840 on an Ebyte E73-2G4M08S1CX. I am trying to burn a bootloader to the chip using OpenOCD and a Raspberry PI Pico W as a debugger...
Hi!
I have been unable to find a single, simple set of instructions for adding MCUboot to a project(toolchain 3.0.0 sdk 3.0.0) that will enable a non-default signing key...
Hi All,
I am currently evaluating how I can charge a single cell with the nPM1300 PMIC with a USB-C connector, with the addition that the same USB-C connector should be...
Hi everyone,
We're using the "Manufacturer Specific Data" field within its advertising packets to send the firmware version to a phone application. It requires the company_indentifier...
Setup: - We have a custom board using the BL654 (Laird Connectivity) module with the NRF52840 core using SDK 17.1
Issue:
- On power up we configure the GPIO 41 as an input...
Hi, I am using ncs 3.0.2 and an looking at adding extra .conf files during production. For the app it works fine using --extra-conf, but I can't figure out how to add one...
Hi everyone,
We're reading BAT level by reading data from ADC pin and the setup diagram is shown below.
We tested our device at hospital, and we observed significant...
