Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I have been trying to understand and get the “ble_app_template” running this weekend, but I keep running into errors. For example in
static void sys_evt_dispatch(uint32_t...
I'm using RS485 driver on NRF51822 uart. I started software developing with ble_uart exapmle.
RS485 as always has direction control inputs.
Before data transfer to uart...
In my app I have the following:
s110
20 ms min connection interval
100 ms max connection interval
4000 ms con_sup_timeout
I'd like to set the slave_latency...
Hi,
The documentation states -96dBm rx sensitivity for 1mbit BLE mode and -93dBm for proprietary 1mbit mode.
Is it possible to use BLE mode (3 in MODE register) but...
I want to scan for peripheral devices in central-role and at the same time i want to broadcast in peripheral-role. How do i have to initialize the Softdevice in this case...
Hi,
I'm originally iOS app developer.
I have been developing with custom PCB that based on nRF51 chip. (not nordic development kit)
My PCB has a gyro sensor and some...
Hi,
Whenever i m trying to upgrade my application using iphone with binary file then i get "unsupported DFU" error. what is meaning of this error and how can i resolve...
Hi please help,
We are facing a problem of Gazell failure (not getting interrupt on gazell ISR) when i perform external Flash write using SPI.
If i disable gazell and...
hello there i downloaded nrf5 iot sdk. i have nrf51 and nrf52 kit.now it has many example codes like tcp,udp. can anyone tell me how to test it with my kits??
Hi everybody
Can nrf51822 advertise with a Balun whose SE pin is disconnected? (not connected to antenna, just left disconnected)
Just like the reference circuitry above...
Hello,
I can see, that sd_ble_gatts_hvx() returns 13313, if the notification is not enabled for that characteristic from the connected central. --> S120 Softdevice runs...
Hi
I got my new NRF51 DK. I was able to test it with blinky using mbed. I had to add the add the device nRF51-DK. then compile it and drag the .hex file into the mbed drive...
When I first got the nRF51-DK board... I was able to see this board on nRFgo. I then added the s130 hex file to it.. Since then when I connect this board, it does not show...
Hi,
Everyone,
I am trying to achieve minimum current level, I can possibly achieve, with continuous BLE transmission
so, I tried running BLE_POWER_PROFILING_APP given...
Hello to everybody.
I've buy a nrf51822 module with a motherboard.
i struggling to programming an uart over bluetooth example but i think something missing.
With nrfgo...
