Hi
I am using the nRF54L15 DK and build a thread continueing monitor the data rate in 1 Hz, if it is lower to 800kbps I want to change to 1M; while above 800kbps I want...
Hi all,
I’m Bruce — first-time poster but have been working with the nRF9160 on and off for a while now, mainly in outdoor, power-constrained telemetry and monitoring applications...
I have a simple GATT server application with two characteristics, RX and TX. In my prj.conf, I am trying to disable pairing as follows :
I can connect to the server from...
Hello,
I am trying to use LTE connectivity on a custom board with a nRF9160 SICA B1, but i am facing issues with the modem.
With both my own app firmware and the sample...
I have searched all responses here and whatever sources I can find, but not have any success. The main problem is that existing materials appear incompatible with the 54L...
Hi, I have test the throughput using two nRF54L15 DKs and make them close to each other.
My result is:
1. My first question would be: the best througput for 2M phy is...
Hi,
We're working on a project using the nRF5340, where we interface an external NAND flash (4096 blocks) to store high-volume sensor data. We are planning to maintain an...
Ok, so please bear with me as I'm quite a greenhorn both in embedded world as in nRF series chips. My aim is to understand how deep sleep works. I might use wrong terminology...
Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
Hello,
We use DFU Service with nrf51 with sdk 9.0.0.
GATT 0x1543 characteristics can be found on DFU Serivce. But the descriptions are not found on documents.
infocenter...
Dear Nordic,
I have developed the software using development kit with latest chip version 3
nRF51422_xx_AC --->32KB RAM and 256 KB FLASH
SDK ---->nRF51 SDK 9.0.0
S110...
Hi,
I'm working on setting up project inside uVision. I have added all files with headers, and when I try to compile this is what I got:
..\SDK10.0\components\libraries...
Hello,
Has someone been able to use DFU with nRF52 device?
I'm trying to add the DFU capability/service to the HRM example.
I have added the BLE_DFU_APP_SUPPORT define...
maybe the document of GPIO Pin sensing mechanism has some wrong in the nRF51 Series Reference Manual (version 1.1).
sense high/low level defined in the document is different...
Hello,
I'm looking to find an example of an iOs code (xCode), in order to control the led with an iPhone (a simple application : on the phone, there is one button, and...
Hello all, I am using nRF51822 SDK8.1.0 SD130
The code was a central, and I want add a peripheral function.
I reference \examples\ble_central_and_peripheral\experimental...
Hi,
I can't find any data on the analog comparator delay in the datasheet. Except the 15 us for anadetect signal. Is this the delay through the comparator for normal signals...
Hi,
I am developing some DFU OTA firmware for nRF51822, QFAAH0 (v3 silicon, 256kB ROM, 16kB flash), on a custom board, using SD110v8. Both my application and bootloader...
I am playing with the nRF52-DK preview and I noticed the samples in the 0.9 SDK are set to 32k of RAM. I increased it to 64k as per the chip specification and had no problems...
Hi,
I'm in a situation where I need to get two devices communicating using S110. I am aware that I can send using S110 and I am only referring to small transfer sizes....
Hi,
I meet a very strange situation when I tried to wake up nRF8001 from sleep.
I send 0x05 to nRF8001, it replies me ACI command 0x40 is unkown (0x82).
I have checked...
