Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I want to port an exisiting solution from ESP32 + nrf24 to nrf54L15. I didn't find any example that would work out of the box for my POC which would to combine very...
Draft — ready to post on Nordic DevZone / Zephyr mailing-list
Title nRF5340 DK + MCP2515/TJA1050 module — can_start() always returns -EIO even in loop-back
Hardware...
Dear Nordic Support Team,
We have a system where an MCU is connected to a Wi-Fi module operating in NCP (Network Co-Processor) mode . The MCU controls the Wi-Fi chip to...
Dear sir,
I'm using the sample application "channel_sounding_ras_initiator" to performing the evaluation. Here are my test environment: - Developement kit: nRF45L151 - Tool...
Hi,
I'm using the nRF52832. And I was wondering if it really does support LLPM. I found sources that clearly state tat it does (e.g. the wireless mouse/keyboard example...
Hey, I have a problem understanding BLE behavior
I had a product was running in BLE phy 1M, and I wanted to convert it into PHY CODED.
It just sniffs all the advertisement...
I attempted to use nRF52840 for multi-connection data interaction, but whenever I was debugging, I always encountered the problem of being unable to establish a connection...
Hello, my application requires very precise timing to trigger an action on the edge of the GPS time. I just need to get this time once in a while to synchronize the system...
Hello, this is probably a very beginner question but I don't know how to configure interrupt for the GPIO headers on the nRF52840 dev kit. I tried to search in this forum...
Hi,
We have been running into issues with our FOTA over BLE using mcuboot. Our usual process has been to use the dfu_application.zip file in the build/ directory (ncs...
Hi,
I´m working on a Zigbee-based environment sensor. You can find all related files here: https://github.com/Kampi/BeeLight
Now I have the following scenario: the whole...
Hello,
I have an nRF52840 based custom board (myboard, NCS2.70)
its partitions node closely follows the nRF52840DK dts file:
both have &flash0 in the /chosen group...
Hello everyone
I need to install Nrfutil offline, computers may not have access to the internet, i follow this istruction and prepare the offline directori whit the comand...
Hi Nordic team,
We’ve implemented a custom firmware update flow for our nRF5340-based device , which supports a robust single-image FOTA process using external NAND flash...
Hi, when I am trying to set up channel sounding, I am looking for the best parameters for CS configuration. The main problem I have is that even with slow movement (1 km/h...
