Hi
our last product is based on nRF5340 and now we start a new design based on nRF54H20, and its essential for our design, i checked alot but there is no datasheet, reference...
just passed Cellular IoT Fundamentals while I was waiting for my nrf9151dk to be delivered... Now that I have the DK I can't get the dk to be provisioned...
I couldn't get...
NCS currently has a nice feature where the firmware versions are printed in the boot banner:
Is there a config option to also enable printing the nRF91 modem firmware...
Dear all,
after cutting the SB bridge to the QSPI chip and close the ones to get the pin free and disabled also qspi inside the nRF52840dk_nrf52840.overlay file I'm unable...
Hey, I have a problem understanding BLE behavior
I had a product was running in BLE phy 1M, and I wanted to convert it into PHY CODED.
It just sniffs all the advertisement...
Dear all,
I stubled upon the following issue when developing a BLE sensor product. When I try to bt_gatt_notify(); With only one characteristic, there is not an issue...
I was looking into the sdk provided by nordic for nrd52840Dk board and want to test the zigbee protocol. I havn't find any sdk for that.
Can you share me some links and...
I am trying to use the nRF51822 to capture all Bluetooth Low Energy packets on a channel. In it's final application environment the chip will have to fulfill several functions...
I performed flash read using nrfjprog --readcode . here the snipped of the output file
:020000040000FA
:10000000FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF00
:10001000FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF0...
Both nrf51 & nrf52 SoftDevice specs say that this can be done:
infocenter.nordicsemi.com/index.jsp
infocenter.nordicsemi.com/index.jsp
There have been a couple of...
So, I am having a nRF51822 application that I used to upload via wired interface. Now I want my application to support so called DFU over BTLE, enabling software upload from...
Hello,
I'm trying to use nRF51 as bluetooth communication module for LPC1769 communicating over SPI, so I use connectivity firmware in nRF51 and now I'm trying to access...
Lets just stick to GPIO
I am trying to initialize multiple input buttons and multiple output LEDS.
I am trying to glow the LEDS with corresponding buttons...
Hello,
I need to know does nordic S120 stack gives the RSSI value on receiving data from peripheral? Currently I am able to get the peripheral RSSI on peripheral device...
I can not compile the example project 'ble_app_uart_s132_pca10036' ,in nRF52_SDK_0.9.2_dbc28c9\examples\ble_peripheral\ble_app_uart\pca10036\s132\arm5_no_packs.the error given...
The Nordic UART code was built for the UARTE using the following definitions:
#define UART0_CONFIG_USE_EASY_DMA true
#define UART_EASY_DMA_SUPPORT 1
#define UART_LEGACY_SUPPORT...
I add my own codes in nRF51-ble-bcast-mesh-sdk-8-support project,
then I find that if device_flash_init() is compile to this project,
the program cannot finish rbc_mesh_init...
Hi,
I have app + bootloader in one packet. On Android nRF Toolbox both can be updated in one step using Distribution Packet option. Is this possible on iOS?
I know it...
The BLE Central tutorial (S130 based) does not connect to my peripheral. My peripheral connects fine to the Android MCP and the 128-bit service UUID is what I expect.
I...
I use nrfgo studio to program the hex file. but I have only 128kb of flash and the softdevice took 88kb which left less then 50kb. I have a hex file of 70kb
my question is...
hello.
I develope the using the Nrf51822, bootloader and application not using softdevice llbrary.
the procedure is that one mcu send the mrf51822 by uart. and mrf51822...
