Hi,
I'm looking to use the nrf connect sdk for development that is compatible with the latest zephyr lts. I believe it will be ncs 2.9.2 compatible with zephyr 3.7.99 (3...
I'm still new to this but particularly in regards to battery. I have a custom board with a nrf5340 and have been working on reading the voltage. I used the battery sample...
This is NOT a runtime error it's a compile time error (application). Failing at stage [154/159] Linking C executable zephyr\zephyr_pre0.elf
Having started by following...
Hello,
I am designing a custom PCBA based on the nRF7002DK PCBA and I really need the Fabrication Notes / Drawing that officially went to the fabricator to direct the build...
Hi,
I purchased nRF52 DK 2 PCs. PCB labeled
PCA10040
3.0.4
2024.34
boath board are new and box packed. from first time itself. I am not able to flash the board...
Hi everyone.
I cutted PCB track shorting solder bridge SB40 .
I connected like this..
Then I opened power profile kit 2. I am using amperemeter..This is my app scrrenshot...
Hi team.
Now i'm use soc nrf5340, and the ncs version 2.9.0.
I want to encrypt my external flash using QSPI.
I encountered some problems while using the nrf connect...
Hello ,
I am initialising application timer with prescale of 327 for 10 ms interrupt delay. I created a timer slot using app_timer_create(&ulTestTimer, APP_TIMER_MODE_REPEATED...
Hello,
We are unable to get the softdevice to work on nrf52 DK(PCA10040) . It ends up at app_error_handler each time. We have followed previous recommendations about LFCLK...
Hey guys,
Trying to use TWI in the lowest power way possible, non-blocking. Is this the right way to do it? When I run this, I get the callback event handler to execute...
Hello,
I'm looking to disable the Bluetooth in the ledButtonDemo,.
In the led_write_handler, I've replaced the code by :
if(led_state == 0)
{
sd_ble_gap_disconnect...
Hi
I tried to check nRF51 SDK on IAR Embedded Workbench for ARM 6.70.2.6310. But he said that the project is broken.
It looks like there are no setting files for all...
hi,
i'm working on change 'example project file using softdevice s110' to 'using s130'.
but, i don't know where exactly need to change.
just downloading softdevice s130...
I need to use the 8.0.0 version of S110 with my beacon which contains 7.1.
Since the Android DFU utility supports updating the Bootloader and softdevice with a zip distribution...
hi,guys
For testing the comunication between BLE+timeslot device and radio device, I change the code as below:
void start_timer(void)
{
NRF_TIMER0->TASKS_STOP = 1;...
Dear Nordic,
Whats wrong with the below code. It works well in RFduino but when I try to port the same code in Keil environment.Its not working throwing error as
1.identifier...
I just got a new target board back from fab/assembly and I'm trying to use the debug out connector on the PCA10028 to program the new target.
My target is the NRF51822...
Is there a beginners guide on how to get a console output working for the following setup?
keil v5 & SDK 6.1
nrf51-dk connected with the
TC2030-MCP-NL to a
nrf51822...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
Hello,
I am new to working with nrf52 and was looking for a way to make printf work in a blank project that I have created. I followed the uart example for the peripheral...
