Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I'm a bit at a loss of how to voluntarily stop advertising: My related thread says I should call sd_ble_gap_adv_stop() , but when I do, no corresponding event is raised by...
To install micro-ecc, complete the following steps:
Install version 4.9-2015-q3-update of the GCC compiler toolchain for ARM. You can use ARM's Launchpad to find the toolchain...
Hello everyone,
I am currently porting a project from pstorage to FDS.
I am testing the functionalities of FDS including create, update and delete records and I am at...
Hello,
To reproduce this problem I use these steps:
Bond to NRF51822 using Android 6.0.1 and latest nRF Connect version;
After successful bond, connect to NRF51822;...
Hi,
We are using PPK board (PCA63511), we have followed the "PPK user guide" and installed all the necessary softwares, We have made the connections and switches option...
Hello everyone, I'm Dario.
I'm trying to work with a ble nano with nordic component. My target is to receive a string via serial periferial and sending it via bluetooth as...
I am a new engineer working with nRF52 and SDK 12 using Makefile project and arm-gcc. I wrote some simple code to try TWI Master and control a i2c slave device. My question...
Hello I just bought
SKYLAB bluetooth accelerometer sensor SKB360 bluetooth low energy nrf51822 bluetooth 4.0 low energy module
skylab.en.alibaba.com/.../SKYLAB_bluetooth_accelerometer_sensor_SKB360_bluetooth_low_energy_nrf51822_module_bluetooth_4_0_low_energy_module...
Hi,
Im trying to wake up from SYSTEM OFF using LPCOMP.
Im using the following code to power off:
nrf_drv_lpcomp_config_t config = NRF_DRV_LPCONF_DEFAULT_CONFIG;
...
Hi,
I am working on a Beacon application based on nRF52 DK and Eddystone protocol. So i am searching if there is already some examples/SDKs from nRF which supports both...
Looking for document or u tube to program nrf52832 using tag connect (6pin noleg) and nrf52 DK. Have the hex program and put it on the nrf582 dk. need to take to the next...
We have identified a possible transient fault condition in which a voltage in excess of VDD can be applied to an I/O of the nRF51. VDD is 3 V and the excess voltage would...
sdk_resources.h does not compile with c++ in SDK12.
The _cplusplus guard only begins if ESB_PRESENT is defined. The guard should either be moved above or below
#ifdef...
Hi,
do you have any tutorial for contiki on windows based.
no matter which platform you are using.
i am using the ecilpse with cygwin toolchain in ecilpse.
i follow...
