Hello,
We are working on Zephyr sample app Mesh on nRF52840dongle with nRF Mesh application.
After going through the documentation and few other Q&A on the portal, I was...
Hlo
I have designed a custom board based on nRF5340. Now I am trying to do flashing and RF testing of it through nRF5340 development board but can't even flash it because...
Hi all,
I'm encountering an issue with the TWIM30 interface on the nRF54L15 (pins P0.03 - SDA, and P0.04 - SCL), using vanilla Zephyr v4.2.0-rc1.
The setup involves external...
Hi,
I purchased a Qorvo QM33120WDK1 UWB development kit that uses a Nordic nrf52840-DK. I have been using this DK for weeks without issues, but the last time I used it...
We are developing a product that will have a wireless and wired option, based on the NRF52840
The strategy is to release the wired option first, followed by the wireless...
Hello,
I'm trying to build the trusted firmware M for the nrf9151.
I did the following steps:
git clone git.trustedfirmware.org/.../trusted-firmware-m
cd trusted...
Hello,
I would like to use the Radio Test Sample from the newest NRF Connect v3.0.2 (v3.0.2\nrf\samples\peripheral\radio_test). However, when I try to build it with "nrf54l15dk...
I searched over the website, I couldn't find a good introductory documentation for programming the nrf51822, specifically the nrf51-dk. I have a transistor hooked to p0.01...
Hi Team,
Is it possible to have multiple profiles like serial, heart rate monitor, proximity etc. in single code?
What are the efficient ways to do it?
Regards,
M...
Hi,
I'v a query regarding the two development boards PCA10001 & PCA10028.
I have worked on a project with development kit PCA10001 and made the release to customer ...
I have followed the instructions and have tried with s110 6.0.0 and SDK 5.2. I can compile and download to the board but can never detect under discoverable device onn MCP...
I am running ble_app_uart in my pca10004 board. The crystal configuration is set to 32khz crystal.
But i want to use the 16mhz external crystal for my use ,because my application...
Hi!
(I moved this question to the "Questions" area from another area.)
I am using Eclipse to develop and debug on nRF51 DMs (PCA 10028). I have managed to run and debog...
Dears,
Just one question for RTC.
In SDK9.0, it's possible to control of time to use HW RTC block??
If possible, please let me know how to use it..
Thank you.
Lets say I have 200 bytes of data that I want to store in flash. So, I request a 200-byte block.
In order to store, the area has to be cleared first. As far as I understand...
Using the nRF51-multi-role-conn-observer-advertiser-master project to test timeslotting I have encountered two issues (Softdevice s110 7.1)
Issue #1: Repetition of advertisement...
Now, I need two function add my project (On BLE stack).
Distinguish long/short press at same button.
2.device and master synchronous time.
No.1 question is...
Hi
We have custom nrf51822 board.
in that we have nor flash which is spi compatible.
so in order to read device id i used spi_master sample source code.
i am able...
Hello,
I'll explain my code:
NRF51 takes samples of a sensor every 10 minutes. In addition, softdevice S110 is used... An user can connect at any time, so advertising...
I am trying to implement frequency counting on nRF51822 by counting number of pulses in a given period. I create a PPI channel with a GPIOTE event on rising edge linked to...
Hi,
is it possible to mount a nRF51822 in an aluminum enclosure and use ble?
I am looking for a range of up to ten meters in an open area.
Is that possible or will the...
