Hi I'm testing the current consumption of the external qspi-flash on nrf5340dk [ MX25R6435F]. I have used ppk 2 to measure consumption with the dk and also have used a power...
Hi,
We are using nrf21540 in GPIO mode + mode pin ( and CONFIG_MPSL_FEM_NRF21540_RUNTIME_PA_GAIN_CONTROL) with an nrf52833.
We are developing under nrf connect sdk 3.0...
During the development of a Matter over Thread product, I encountered the following issue:
After adding two Matter over Thread devices (an OnOff Switch and an OnOff Light...
Hi Nordic Teams :
I would like to check the current consumption by BLE DTM.
1. Is the table measurement is from 3.0V input?
2. I find the condition in the datasheet...
HI ALL,
nrf54l15dk,v2.8.0,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
At this...
I'm developing my application with nrf 52832 and nrf SDK v17.
I know NCS is more powerful. I'm currently learning how to use it.
But now.I still need my application with...
I'm writing a wav file from the nrf52840 board to the nor flash w25q128jv with a capacity of 16mb but it seems that I can only operate on the first 2mb, even when dividing...
I need to connect to a beacon with a scanner nRF51 using the advertising data of the beacon. Then i need to get the service and characteristics of the beacon.
Thanks
Hello everyone,
i am trying to compile the Ble-UART_example but everytime it shows this error 'GPIOTE_config_irq_priority is undefined ) and i dont know what went wrong...
I have tried to flash my application targeting nRF51822 on our board by using a Segger on nRF51 DK. However, Keil compiler always shows that it couldn't find any nRF51822...
Hi NORDIC
I have to complete a function that one can transmit and the other can receive . but I do not know how to set nrf51822 to be a receiver . please tell me or share...
Hi,
it seems that the default implementation of the ble_bas (battery service) provides the notification feature but not the "read" feature.
I client can enable notification...
I'm using the Github project github.com/.../nRF51-multi-role-conn-observer-advertiser in order to SCAN in a specific channel rather than all 3 channels. In this example, softdevice_handler...
Dear all,
Recently,i use nrf51422 trying to receive data from two ant sensor.
i assign two ant rx channels at the same time, i find i can't receive data if only one sensor...
We are planning to use a synchronous independent channel, that senses whether there are any slaves or not using acknowledged data type.
More than one slave could have paired...
HI,everyone!
I want to use pstorage to store some data, so I followed the steps given by devzone.nordicsemi.com/.../ , but it didn't work.
Then I checked ecah function...
Hi all,
I want to test power consumption of data packets reading from SPI to RAM using PPI.
But i'm not sure that can RAM act as a peripheral of PPI...
So, can i use...
I am using a solar powered energy harvested circuit to power the nrf51 module. However, when the generated voltage drops below 1.8v, the nrf51422 enters into brown out reset...
Hi,
Now as I want to ensure low power mode with minimum hardware and firmware, I have written very small code to check it. Simply, I have initialized timer only and go...
I have used your example of a bootloader nAN_18. I can create a basic program, with new firmware, and also load my new bootloader program at the high end of memory.
My...
Hello,
In what code structures (from SDK) the storing bond information for the Android and iOs devices (random static or public addresses and private resolvable addresses...
Based on Battery Service I have made my own Service and Characteristics but I have problem with setting Indication. This is how my characteristic add function looks like:...
