Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Hi,
I'm developing BLE functions using nRF51822 on top of the Android Kitkat applied device. I cannot find android bluetooth HAL source code that Nordic provides. Is there...
In my application I have a custom board with a single LED. While advertising the LED blinks at 1Hz and when connected the LED goes solid. However while testing with a proven...
I'm creating an application based on the s110 SoftDevice found in nRF51_SDK_8.0.0_5fc2c3a. I'm new to the SoftDevice framework so I've probably made an error somewhere but...
Is the GPIO pull down/up asserted on the 'inside' of the input disconnect switch or at the input/output pad? The diagrams would indicated that it is on the 'inside' of the...
This is function definition:
static uint32_t battery_level_char_add(ble_bas_t * p_bas, const ble_bas_init_t * p_bas_init)
This is declaration of the automatic variable...
Before starting advertising, we want to write some configuration information to NVM. In order to write to NVM, we first call sd_flash_page_erase and wait for the response...
I just posted a package of simple tools I wrote for OSX over on Sourceforge . The main app is a Cocoa app which lets you choose code, softdevice and bootloader (last two optional...
I Saw iBeacon Packet in the website
(d6 be 89 8e) Access Address for Advertising
(40 24) Header
(05 a2 17 6e 3d 71) Mac address
(02 01 1a 1a ff 4c 00 02 15 e2 c5 6d...
I want my peripheral device to act as a beacon while it is in a connected state with a master device. Is it possible to start not-connectable advertising in parallel with...
I am working on a nrf51822 UART bootloader using Keil 5.14 (though I had the same problem with 5.1). If I start with the pack example dfu_dual_bank_serial_s110_pca10028 with...
What happened to NRF_FICR_Type.INFO and FICR_INFO_Type in nrf51.h?
This was in ./components/drivers_nrf/hal/nrf51.h in nRF51_SDK_7.1.0_372d17a
but is missing from ....
Using the nRF51422 with the TWI hardware version. Just playing around to verify signals with the following code which just configures the TWI1 and then repeats continuously...
Hi,
i tried to update the firmware of nRF51-DK but it crashed and now Keil uVision says "Cannot find the JLink version number"
Its also not showing in the nRFgo stu...
I'm developing application using your devices (PCA10001/PCA10000) and S130 SoftDevice. I tried to implement DFU/OTA feature in my app. For this purpose I used DFU sources...
Hi All,
Does anybody has a working setup using SD 7.1.0 with SDK 7.2.0, iOS 8, DFU with a secure connection?
When I use no encryption it works, but when I enable encryption...
