I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
It is good practice to prefix the includes from one's C libraries with a directory so that they are all part of the same 'include namespace'. Unfortunately the Nordic SDK...
hi, guys.
I'm prepareing the Korea certification, KC, with nRF51822 BLE system.
I'm progressing to get KC by certification agency.
Today, They will have RF signal test...
I was comparing the binaries for the S120 and S110 stacks and see the MBR is different.
I was under the impression that the MBR never changes and was thus expecting it...
Hi Nordic
We want to test radio parameter through IQxel . Now,we need a application software to control nrf51822(TX,TX,outpower,channal and so on ) . Can you recommend...
I'm using the example code for simple device/host Gazell in SDK 7.1.0 as my starting point for my application.
My program runs for a second or two, then ends up in the...
Hi
I am new to programing low energy devices. I got a Blend Micro from RedBearLabs. I am using the
nRF Master Control on android to connect to it. I am able to change...
As I create my first 'profile document', it would be nice to read over some examples. My only knowledge of this document comes from nAN-36, section 2.2.2.5 :
A profile...
Hi
in the SDK 7.1 examples, there are examples about how to use the hardware peripherals, and examples on how to use the BTLE stack, but nothing combined.
How do I combine...
Hello, I've started bluetooth development with nRF51 DK since yesterday.
My devlopment platform is KEIL-MDK(v5)
Yesterday, I just tested my board, download the blink...
I have an nrf51 dev board which i can currently connect to an android phone and read data from. I would like this board to be able to scan for other BLE devices and send data...
While attempting to understand why my S120 v 1.0.1 application aborted in:
sd_softdevice_enable(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, assertion_handler);
producing:
ASSERT...
In regard to the following functions
uint32_t sd_nvic_critical_region_enter ( uint8_t * p_is_nested_critical_region )
uint32_t sd_nvic_critical_region_exit ( uint8_t...
Hello, from looking at the GCC linker files I take it that S120 softdevice doesn't support using the full 32KB RAM of the new nrf51422-xxac devices. Is this something that...
Hi, I have written a simple program to calculate the number of retries with nRF24L01+.
On transmitter side, maximum number of allowed retries is set at 1. The transmitter...
Hi all,
I am a beginner with nRF24LE1, when I want to code some examples using GPIOs, I find that it's difficult to understand the PxCON register function. Whether I configure...
I am using the usb port to download an example project to the NRF development kit board, with Keil4. Somehow it keep telling that "No jlink device found", in Keil, the project...
