I am working on an application and need to get the exact time that the master node receive advertising from the slave node. I tried with PPI and it's ok to capture the Radio...
Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hii,
I am trying to update new firmware in nRF51-DK.
But unfortunately, wrong image file is uploaded.
Now i am trying to once again same process then getting no space...
I am testing the SDK (v12) Power Profile Example with the DK51 and the nRF51 dongle. My purpose is test if I can lower the power consumption as mush as possible. The default...
I am developing software for a custom hardware based on NRF52. Previously I was tasked on updating the old NRF51 based software (used on older version of the device) for NRF52...
hi,
i am using FDS to store some Data in nRF51 Development kit using temporary application. it is around 2kb. after that i am flashing main Application. is my application...
I am working on a battery-powered application. Since power saving is a must, this design using high-side power node controllers (part number MIC94042) to power-on or power...
Hi
I am looking for pin numbers for the nRF51822 microcontroller.
example like what are the pin numbers for VDD to measure battery voltage..??
I mean in which header...
Hello!
I'm learning how to use properly the saadc for knowing muy battery state of discharge. First of all I'm testing the saadc example which is included in the SDK, changing...
Hi, Nordic
I know when esb working, channel , address and pipe is very important.
From sdk and demo, I can not know these items clearly.
I know these items should be...
I need to use sd_ble_gap_adv_data_set directly and pass custom advertising data, as I need to maximise space and not send the name etc
I have been using mbed which has...
\nRF5_SDK_12.1.0_0d23e2a\examples\ble_peripheral\ble_app_uart\pca10028\s130\arm5_no_packs
I cannot find the define of pin6 pin17 pin21 pin 22 pin24
in this example ...
Hi. Can we develop and use our own firmware for any of the Nordic's beacon? Or do we need to mandatorily use firmware given by Nordic with beacon and modify them as much as...
I am using fds as my file system.
peer_manager is using file system too.
fds_register() is used to register callbacks. But how does the software know which callback is...
Hello
My nRF51 with S120 BLE stack is running as central. I want to connect 3 other nRF51 peripherals at the same time. So in the first step I did a scan and stored the...
Hi,
I'm developing an application based on the nRF52832 and I need a large throughput of over 100kbps, preferably over 200kbps.
I have managed to reach around 128kbps...
Hi
According to BT 4.2 Spec Vol 6, Part F, Section 3.2.9:-
" To write the entire value of an attribute larger than (ATT_MTU-3) octets, the prepare write request and...
