Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I catched the air data packets by Sniffer and it shown that there was an error, MIC incorrect, which could be seen as followed, and the whole packet was malformed....
Hi!
I have some problem to reconnect an already bonded device containing a chip nRF8001 rev D with my iOS app. Rev C works fine with the first connection and the reconnection...
HI,
I want use some GPIO to detect "pin_high_to_low" or " pin_low_to_high".
and I think the "app_gpiote.c" might be helpful.
but I have been confused by function " sense_level_toggle...
Hi,
I'm starting to implement DFU using IAR's ARM workbench. In the example project for ARM that comes with the nrf51_sdk_v5_2_0_39364 SDK there is a file called bootloader_util_arm...
Do I have to use external host MCU for nRF51422? What can the ARM Cortex processor inside SoC 51422 do and cannot do?
I want to create a mesh network with hundreds of ANT...
I want to load a Blinky project to the AK board, and the dongle is used as a jlink, but I forget to move the jumper to the 'out', and the program is loaded to the dongle....
Hi,
I change the example ant_broadcast to acknowledge mode, but it seems that without a peripheral side,the LED0 will still twinkle.I don't know how to change the project...
Hi,
I'm porting a nrf51822 evaluation board 10001 tested application to a custom board. Part of the application is using UART interrupts to raise a flag and start data...
I am experiencing an error in the final linking stage of my build.
_build/blinky_gcc_xxaa_s120_xxaa.bin: file not recognized: File format not recognized
collect2.exe...
Hi
I am looking at section 9.1 of the S110 Softdevice Specification v1.3A and the release notes for 7.0.0-2.alpha where I see that an application now starts at 0x15000...
Hi
S110 v7.0.0-2.alpha got released today.
In the release notes it says...
[b]The SoftDevice can now be configured to forward interrupts to one of several applications...
My application seems to be running out of memory, now I received NRF_ERROR_NO_MEM from sd_ble_gap_ppcsp_set. I don't understand why this has started since I don't think i...
Im using custom board with nRF8001. I'm using Hello World example from GitHub.
The nrf chip revision is C not D. When I connect the board to Arduino Leonardo the device start...
Hi
I ran the example " ble_app_hrs ". the consumption is 1.5mA, when I hold SWCLK and nRESET low,the consumption is fall to 0.9mA. how I could reduce the consumpion??
