Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hi, I am porting my project from nrf51822_5.2.0 to nrf51822_6.0.0.
I want to change bond manager to device manager.
I refer to the heart rate service in sdk 6.0.0 and...
I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
tldr; read the release notes first and use the batch file provided in the folder
Hi,
I'm trying to load the S110 v7 on an nRF51822QFABB00 and I'm getting the following...
Hi,
I am developing a multi-protocol communication device using BLE, ANT and 868Mhz "long-range" communication. I am using MRF49XA chip for sub-ghz communication. I have...
I have just updated to the latest SDK, including the S110 Soft device v7.0.0.
I have now noticed that I can bond using the Master Control Panel, but I cannot bond using...
On June 25th I asked a private question regarding be able to use the S110 soft device with the nRF51422. The following is the response I got:
....
Yes you can use the...
I am unable to to send notification for a customized service. I am testing a customized services that simply increments a variable every 3 seconds and sends notification with...
Hi guys,
I am trying to use the timer 1 on the nrf51822. I found the sample code online which could probably do the job for me. But I wanted to know what is the standard...
Hey Guys,
i asked this question already few days ago, but today i produced a log-file.
The procedure was:
Setup: SDKv6.0, SoftDevice v7.0.0, nrf51822
empty board...
Hi guys,
I had look at the ble_connectivity example in \nrf51822\Board\nrf6310\s110\ble_connectivity floader,but I can't found any documentation about this project.Is it...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
We found that in some cases. e.g. we started a background ble service. The ancs characteristics will change as the picture below. Do you think it's normal? Does the Nordic...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi guys,
i'm just porting my app from SDK5.2+SDv6.0.0 to SDK6.0+SDv7.0.0 and stuck with the device manager. There rises some questions, and i hope someone can help me....
