Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hi,
As I’ve mentioned in a previous post (answered ! Thank you Aryan !), I'm writing a bootloader for nrf51822 to be able to update the nRF51's firmware through SPI (data...
Dear community and support,
I am trying to install Master Control Panel 3.9.0.6-x86 on a Windows-XP virtualbox. The installer fails with the following message :
"The installer...
I want to send a float as a value of a characteristic.
As I know is this all what I have to change to send a float...
float temperature;
uint16_t len = 20;
attr_char_value...
Hello,
i have an urgent problem that i need help.
I have designed a board using nrf8001 IC and manufacture 5 samples. They are working perfectly.
Then i went to production...
I am using the S110 softdevice from v8, and building the bootloader from SDKv8, using keil uv5.
The project is dfu_dual_bank_ble_s110_pca10028, loaded from the dfu_dual_bank_ble_s110_pca10028...
Hello, Greetings, in the nRF24L01 datasheet, it's mentioned that the module can work as a multiceiver using the six parallel data pepes,my question is that if it is possible...
on an arduino+redBear Shield 2.1, I read an analog port and write the value to the serial monitor and to my bluetooth connection with
ble_write(analogRead(0));
Serial...
I can't find anything related to this in the docs :(
In the client_handling.c is a function static void on_evt_hvx(ble_evt_t * p_ble_evt, client_t * p_client, uint32_t...
I have been unable to get an ISP130301 module to work with the example dfu s110 bootloader. Dual band, single bank, all of the sdk and SD variants. I've followed the tutorial...
I want to store sensor measurements taken every 2.5ms persistently. Does a write to the internal flash happen faster than this? Can I safely assume that the internal flash...
Could somebody, please tell me what it means? I couldn't find it in the docs.
uint32_t bleDeviceManagerInit()
{
uint32_t errorCode;
dm_init_param_t params;
dm_application_param_t...
