Background
Our device uses the CONFIG_LTE_NETWORK_TIMEOUT option from LTE Link Control, which by default is set to 600 seconds (10 minutes). I haven’t found any specific...
Hello, as the title suggests, I have an issue when powering the nRF9151 DK with an external power supply. Normally, I power through USB, and it's fine. However, when I followed...
Hi all,
I am using and nrf9160, in particular a thingy91. It is running 1.3.7 firmware. I have the SLM sample loaded and can sent AT commands to the device using the nRF...
Hello,
We are working on Zephyr sample app Mesh on nRF52840dongle with nRF Mesh application.
After going through the documentation and few other Q&A on the portal, I was...
Hlo
I have designed a custom board based on nRF5340. Now I am trying to do flashing and RF testing of it through nRF5340 development board but can't even flash it because...
Hi,
I purchased a Qorvo QM33120WDK1 UWB development kit that uses a Nordic nrf52840-DK. I have been using this DK for weeks without issues, but the last time I used it...
We are developing a product that will have a wireless and wired option, based on the NRF52840
The strategy is to release the wired option first, followed by the wireless...
I've been using PPK2 to test our work for maybe around 3 years. it's always been steady and stable and can run for several days without problem. Mostly I'm using the PPK2...
Hello!
We are planning to implement OTA update of an application and a second stage bootloader in our product. As a bootloader chain, we will use NSIB + MCUboot as the nRF...
Hi Team,
I am currently working on a project involving the Nordic nRF DK IDE and the Matter protocol. As part of my learning process, I watched your YouTube video and followed...
I'm an engineer to develope smart ring, it's a very small devie and need to use very small IC.
I'm looking for nRF5340 + nPM1300 reference schematic for this development...
Hello,
I'm currently working with a custom board using the nRF5340 SoC, and I'm running into unexpected current consumption behavior.
When the device is in advertising...
Hi,
I was at the webinar today where they talked about SDK 3.0.0. They mentioned that the QSPI examples were "JESD216 flash" and "JEDEC SPI-NOR flash". I don't see either...
Hello everyone,
I'm trying to set up the Wifi stack on the nRF7002 and use it with MicroPython, but encountering a lot of difficulty with it. I cropped up a network_wlan...
I am trying to implement LittleFS on 1Gb QSPI NOR flash (W25Q01JV) on the nRF5340.
I am running nRF Connect SDK version 2.4.2 and am using a slightly modified version of...
Hello. I am using nrf52832 for Ble-based positioning. currently i am tackling with establishment of an anchor measuring rssi values and sending them to a central center (a...
Hi,
I am trying to run the nRF91x1: DECT NR+ Shell example on my nRF9161 SDK board.
I get this crash when the code runs
Can you point me to the explanation of what...
We're building a prototype board which uses the nRF52833 and want to tune the RF components. The radio_test sample in SDK 3.0.0 doesn't seem to support the nRF52833 SoC. Is...
Hello,
I've an issue that I can't find clear instructions for the nRF5340 serial recovery for the network core.
Being able to update both cores from the bootloader level...
It seems the "reset" button on my nrf52840dk doesn't do anything anymore. I believe this started happening after I enabled mcuboot in sysbuild. Is this expected?
When we were using nrfjprog to flash, we used "west flash --erase" because it was quicker to erase entire flash then sector by sector. However, when we upgraded to SDK 3.0...
