Hi,
I am trying to program the custom nRF9160 board using SEGGER JLink/SWD programmer , For same of the boards when connected to custom board and trying to select the device...
Hello,
we are using a nRF5340 with NCS 2.9 and want to signalize a
UART_LINE_CTRL_BREAK
on USB CDC_ACM to the PC.
Is there a direct way to do this?
Many thanks in...
I am analyzing the power consumption of a custom board with an nRF52833 BLE SOC and nRF21540 FEM for different BLE parameters. In one of my experiments I vary the amounts...
Is there a straightforward way to output the frequency of the 32.768kHz crystal oscillator to a GPIO pin? The motive for this request is to verify the crystal frequency without...
Hello,
I'm developing for nRF54L15 the application with the NSIB + MCUBoot. I have a problem with fprotect in mcuboot returning EINVAL error. That happens due to limitation...
Hi all,
do different settings of SAADC RESOLUTION register affect Conversion Time t CONV ? I cannot find any dependency - the only value given for t CONV is 2 µs typ (7...
My product has nrf52840 with usb mass storage configured using 8MB QSPI flash (same chip as the nrf52840dk - MX25R64)
I would like to allow users to upgrade firmware by...
Hello, I am writing a fairly complex application using the Arduino SDK and an nRF8001. I have a lot of what I want to do working based on looking at the code in the different...
Hi All, I am a newbie....What is the starting point and procedure to develop nRF51822 working with Iphone or Android over HID protocol? Is there any example?
Is it too tough...
Hi,
In the API, the user gives the 'distance_us' parameter for the next requested slot. I have noticed that this is quite accurate (to the micro) and wanted to know if...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
Hi All.
I made my PCB with nRF51822 and achieved around 150 Feet range (LoS). My target is to calculate a approximate distance (in Feet) from RSSI values.
I did a field...
I want to set up the HRS demo, but in reverse. I want to use my PCA10001 board to receive heart rate data from a peripheral device (already working and tested on my PC). It...
Hi,
i have a problem in my Code, when ic look nrf_delay_us (1000) on the oscilloscope i can se a puls withe 1,3 us thats not accurate enough. What could be a reason for...
Hi,
I have created Eclipse project to compile nRF51 DFU loader. This is a pure Eclipse project, no makfile. It has compile configurations for combination of Single/Dual...
Hi,
I am looking to build a beaon product based on nRF51822. There are several kits available shown below. Which kit should I pick to start the hardware design and firmware...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
Hello,
I am using nrf51822 evaluation kit with ble_lbs (Led button sample) profile, I need the USB dongle source code for ble_lbs (Led button sample) profile because I...
Hi,
Is it possible to change the advertisement parameters of a beacon device without connecting to it?
(ex: major,minor value & interval)
Is it OK if our beacon product...
I use ble_app_uart demo of pca1001 and my SDK version is 5.2.0. I want to use APP_BUTTON_INIT to handle a button event. So I changed the buttons_init(void) like this:
static...
Hi, is it possible to add for example a
www.ti.com/.../technicaldocuments
On the nrf51822?
I would have to modify the S110 source to turn on and off the LNA and PA when...
Hi
I have created local buffer of 100 bytes.
while device is connected to dongle it is sending all 100 bytes over bluetooth stack .
but once it is disconnected and...
