There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi, im implemented several services and characteristics in the nrf51822 with S110, its all working (read, write and notification), tested with an iOS app.
Now i need to implement...
Hi,everyone
I want to make out 4 channel PWM with PPI and two timers , PPI configuration like this,
/* Configure PPI channel 0 to toggle PWM_OUTPUT_PIN on every Timer...
Hi All,
I would like the nrf51822 sleep, wake up and then continues advertising.
I try following code:
NVIC_DisableIRQ(RTC1_IRQn);
NRF_RTC1->EVTENCLR...
hello, everyone.
i am a new, i can't understand the meaning of "One event can trigger multiple tasks by using multiple channels and one task can be triggered by multiple...
Please provide me some details about how to implement watchdog functionality so that i can reset the entire system for avoiding software Hangs
I have come up with a code...
Hi,
I have downloaded the SDK 6.0 which contains the ble_app_uart and tried to compile it using GCC, but getting the following error which doesn't make any sense because...
I see the nrf51822-DK and and nrf51822-EK are now marked 'not recommended'. Why is this?
I now see an nRF51-DK and an nRF51 dongle. Are these now the current development...
Hello,
I want to use broadcaster mode for nrf51822, could you tell me please what I must to do to use this mode?
I suppose I must to set BLE_GAP_ADV_TYPE_ADV_NONCONN_IND...
Hi,
We need to develop piconet where each device able initiate receiving and transmitting data.
According to a Bluetooth Core V4.0 specification this topology named like...
Hi Nordic DEV Team,
In my application, I would like to use sd_flash_page_erase to erase like 100 pages user data; the problem of pstorage is that I cannot specify the page...
I am connecting my development device acting as a BLE keyboard using HID over GATT and it seems to be draining the phone battery very quickly. Every 7 seconds I would get...
I am using a US-100 ULTRASONIC SENSOR MODULE, and I need to measure the pulse width that this sensor produce. In arduino we can use a metode called "pulseIn", that gives you...
Hello-
I'm trying to load the Blinky example, I am using the nRF51822 Evaluation board.
I am able to compile but cannot load the board, a window with "Cannot Load Flash...
I use the Timer2 and the PPI for toggle a GPIO to control the frequency of 16Mhz Quartz is correct.
But when I stop the function I have a permanent consumption of ~ 6 mA...
