Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
Hello -
I'd like to make sure my RAM/ROM layout for the nRF51822_XXACis OK - if someone has a minute to double-check it that'd be great.
I started with the "nRF51822 Beacon...
Has anyone been able to get the examples to work on PCA10028?
I went through the following steps:
Used nRFgo Studio to flash in s110_nrf51822_7.1.0_softdevice.hex
Downloaded...
Hi,
Could I write or update flash without softdevice ?
Due to I must update softdevice on our product, but it doesn't have any JTAG Interface,
so, I want to use our application...
Hi,
I want to start TIMER1 by a GPIO_TE.
When the program enter the TIMER1_IRQHandler(), I want to disable the ppi.
And when the program leave the TIMER1_IRQHandler(),...
Hi,
I'm on OSX, and I'm having problems where the first service calls I make on my own device fails but work fine on the second generation Nordic development board.
...
In the changelog for 7.1.0 is says:
"This version deprecates all previous 7.x.x versions"
But in the compatibility matrix, it seems like 7.1.0 is only supported by revision...
i had used flash manager that is in BLE libraries to store datas for persistent storage. but it seems can't work after i enable the softdevice. so i try to use pstorage, i...
Hi support !
In my current application, I use nRF24L01+.
I want to change this nRF24L01+ for a nRF51422 to add BLE connectivity.
So, I've started my development with...
I'm using SDK 7.1, PCA10028 eval board, SD110 7.1, MCP 3.6.0.8331
I have 2 characteristics, and both are 32 bytes long. When I try a "Write Long" from the MCP a
BLE_EVT_USER_MEM_REQUEST...
Hi,
Merry Christmas!
I have a question about pstorage_store.
Actually, I want to store some data in the memory. Each piece of data has its own size (between 1 byte to...
Can I config AIN0 and AIN7 as the input pins of ADC, and config P0.01 and P0.02 as TWI, and config P0.03 and P0.04 as GPIO?
Or I must config ALL AIN PINS as ADC?
I am sending setup commands to a NRF8001 D device and I receive a command response with status of 0x89. This appears to respond to ACI_STATUS_ERROR_UNSUPPORTED_FORMAT. I cannot...
Hi,
I've followed the steps mentioned in this thread devzone.nordicsemi.com/.../ and everything seemed to work fine. I've successfully uploaded "nrf51822_beacon_app.hex...
