HI,
I am using the nrf_desktop sample in NCS V3.0.2, I want to buil with prj_release_dongle.conf , the setting
but build fail, I check the file Path: it should be F...
Hi:
I'm doing exercise 1 of lesson 1 of the nRF Connect SDK Intermediate course. It says: Get the source code of this course as a third-party repository within the SDK itself...
I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hello，
I have a problem with using custom external Flash. QSPI communication.
nrf52840 + NCS2.9.0 , sysbuild.
Flash chip is GD25Q32, datasheet link
An error occurred...
Hi
We know PMIC nPM1300 can transfer battery information through I2C to nRF54L15 to run fuel gauge algorithm
Can we user other PMIC(like MAX77654) that also have I2C I...
Hi Sir,
As check below link, the battery profile can support on non-Nordic MCU.
(+) Does the PMIC nPM1300 support Fuel Gauge feature for MCUs outside the nRF SoC family...
Hello Nordic forum,
I must not quite understand how CoAP callbacks should work. Would anyone be able to give me any advice as to why my modified coap_client results in undefined...
I tried to find an explicit statement whether a new IMEI needs to be written to nRF9151.
These sources state that nRF91x1 ships without IMEI and it needs to be written:...
Hello, I have a project based on nRF9160 and nRFCloud (CoAP), and uses a SIM from 1NCE. This SIM allows to connect to 3 different MNO at my location in France (Orange, Bouygues...
Hi I want to know if I can use the nRF52850-DK to flash the Xiao Sense Plus from seeed? I am following the following tutorial which says I need to use a J-Link but that's...
What is the default transmit power of the nrf5340 when performing an AoA test in connected mode? How do I change its transmit power to perform AoA accuracy tests at different...
Hi,
I tried to change security level, but it's not changing.
When i set CONFIG_BT_SMP_SC_ONLY =y, it's working well with security level 4,
but i want to change mode1...
Hello everyone,
I am a beginner looking to dive into the world of HID (Human Interface Device) development, specifically using the NRF52840 microcontroller. I recently...
One of our products that's been in the market for a couple years is a bit behind on the NCS version (v1.4.2). I am currently doing the 18031 RED Cybersecurity documentation...
Hello,
I am a beginner when working with nRF. I am trying to run the l4_e3 solution code, but it doesn't seem to work. I can connect via BLE, but nothing is being shown...
i want to advertise my one device into coded and into another device i want to do coded distance measurement it is possible to do in nrf 52840 version 2.5.1 ?
Helo, I have ISP1907 for BLE AoA.
In my understanding, the antenna spacing should be half of wavelength, in case of BLE, it would be 2.4GHz thus the spacing should be 6...
