void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
Hi all
In my application where I'm using the Soft device 6.0, I have a simple function which is very time critical. However, this function is not called very often, but...
Hi,
Please can you send me the ble_app_uart source code as it is missing from the latest 6.1 SDK.
I have the PCA 100003 & PCA10000 boards.
Many thanks.
Hi,
In my application I use 5 devices and 1 host to communicate.
I have only a few packets to transfer so the data rate can be low (22Byte/transmission).
The devices...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
I have implemented a boot loader for DFU based on the sdk v6.1 DFU project.
After a when an upgrade is triggered within the application soft reset by the application:
...
Any idea how I can control the TX power within the Timeslot API in SDK v6 SD110 v7?
Are there something similar to "sd_ble_gap_tx_power_set(tx_power)" in the Timeslot API...
Hi All,
We are running some data throughput test on Samsung S3, Note2 & S4 with 51822 and have seen some interesting phenomena as describe below:
1> On both phones,...
Hi,
I couldn't able to program my custom board using both nrfgo Studio and keil. Actually i have two laptops with different versions of j-link driver installed, but suddenly...
Currently I am searching for s130 example code. I know it's in alpha stage, but I think it should be possible to start to experiment with it, isn't it?
In the past I've...
Hi,
I tried following code to close the ANT+ channel on channel not connected to the other ANT+ device:
#define CBSC_TX_ANT_CHANNEL 0
void ant_adv_timeout_handler(void...
We have a DFU which uses a different set of of services than the main app.
Both of them share bonding information which is create by our main app.
Once we switch to DFU...
I am trying to build a system with a single PRX and up to 5 PTX devices.
Initial development work was done with a single PTX with it's address on Pipe0 in the PRX. I have...
I have a CC2540 and CC2541 chip with me. I did figure out that both of them are working, but now I am stuck up at how to practically test if the proximity profile is working...
