Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
We are planning to optimize the radio-frequency signal,so the some docunments like Simulation model are needed.which can help optimize the RF signal through ADS simulation...
In ble_advertising.c, line 165, you can see such interesting code. I assume it is a copy/paste error:
if(p_advdata->p_tx_power_level != NULL)
{
m_advdata.p_tx_power_level...
For the first, impressed by your intoducing NRF52 chip.
Question: what`s NRF52 indoor range using onboard antenna and maximum output power (+4dBm)?
Thanks.
Hi~
I am struggling to get the BLE packets detected by nrf sniffer (v1.0.1) using wire shark. Its only showing "ADV_IND[Malformed Packet]" periodically. I didn't understand...
I believe what I am asking is extremely specific, but keeping hope that I might get some direction
I have used a clone ST- Link v2 programmer to download code into a NRF51822...
Hi all,
I would like to trigger some actions on difference devices communicating with the ANT protocol based on the distance they are from each other. A simple example...
Hi
The documentation for the new feature in S110 v8 to change the gatt table size says that to change it the linker configuration needs changing .
This means it is a...
Hi all,
First of all thanks for Nordic team for the excellent support. It is very useful for a beginner like me to get started on BLE development.
I am using the nRF51422...
The issue is that if a peripheral needs to enable interrupts (or anything else partly protected by the SoftDevice) and is configured before enabling the SoftDevice, the NVIC_...
Hi, I use nRF24LE1 configured for power down on register retention mode with RFRx active.
When the CPU is on power down i don't have any interrupt from RFIRQ.
Init configuration...
I downloaded the power consumption example code to a nRF51-DK to measure the current consumption during SYSTEM ON and SYSTEM OFF state.
For the SYSTEM ON state, I used...
On our custom board, we have a dedicated hardware reset IC which toggles the nRF51822's nRST line low in response to a magic button press. The nRST line has an external 100k...
Hi,
it's possible to decide if send a scan req to a peripheral device? I want to send a scan req only to the peripherals that have a specific adv packet...it's possible this...
So, I am working on a handful of nRF24L01 to test some ideas out with radio devices and read thru many example source codes, libraries and datasheets and now I am going a...
