Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hi,
I want to use more than 8 devices with gazelle protocol, so is there any way to expand the pipe number or change the pipe addresses in runtime ? Host device will know...
Hello, I have a problem NRF905. Sending distance is 0-30 cm maximum.
I want to ask if the defective product or it may be due code?
TX RX uses the base code of the library...
Hi Team,
In current application, each BLE node (nRF51x22) need to switch between Broadcaster and observer roles . Beacon kind of behavior is required i.e. no connection...
Hi All,
Please, I have some questions about the use of iPhone wireless shutter release button:
Q1: Is it possible to connect to an iPhone wireless shutter release button...
Open the nRFgo Studio and connect PCA10028 (NRF 51DK Board) then Erase all data
Open the uVision V5.18a
Open the DTM project file of the example in the following...
Refer to the NRF 51DK Spec page, It can be support Bluetooth 4.2 spec.
In the Bluetooth 4.2 spec, The device can support the maximum PDU size of 255 bytes
Where can I...
Hi Everyone,
I face a problem regarding uploading Application Hex file, I use nRF Toolbox v 1.15.0 mobile app to upload the firmware, Bootloader is successfully uploaded...
Helo, i'm working on firmware for a device, which should be able to scan for other devices, advertise data and be connectable. Scanning and advertising works. Problems come...
Hi All,
Am using NRF52 ,S132 soft device , I am trying to send two packet of twenty byte every 5s . in a timer interrupt handler I call ble_nus_string_send twice continuosly...
I have following set up for current measurement.
NRF52 DK PCA10040 v0.9.0
nRF5 SDK v11.0.0 : Power Profiling Application
S132 SoftDevice v2.0.0
nFR Master Control...
hi
does my nrf51422 v2 have uart over ble?
its version 2 and its supported sdk is 6 and it does not have ble_nus.c
does my nr51422 v2 support uart over ble?
Hello,
I've been playing with BLE applications with my custom board with nRF52832.
I have flashed "flash_s132_nrf52_2.0.0-7.alpha_softdevice" from ble_app_template project...
Hi
I'm having issues implementing ADC sampling to my ble project.
I'm using the nRF51-DK with SDK11 and S130. I used the example from github ( github.com/.../adc-example...
I want to update over BLE with using DFU tool. But do not start updating process.
DFU tool indicates "Enabling DFU Bootloader".
Bootloader stops at memcpy() of dfu_ble_peer_data_set...
Hi there,
I am now in FCC stage and finalizing a FCC code using the radio test sample code. I do have a delimma on what type of radio mode I have to use. Will you please...
