Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
Hello,
I'm a newbie in this area, and I'm trying to program NRF51822 QFAA on a custom board according to the given tutorial for a dual bank bootloader ( devzone.nordicsemi...
Hello,
Since I am still a little confused, could anyone tell me what S110 and SDK I should use for nRF51822 QFAA? ( infocenter.nordicsemi.com/.../nRF51_Series_Compatibility_Matrix_v2...
i am going to buy nRF51822beacon but i do not know what to buy with it ?
i will buy nRF51 DK but i also want to use a segger programmer with nRF51822beacon.
what confusing...
I was wondering if you could advise me on the best way of adding in BLE functionality to an existing ANT application. Is it simpler to have both transmitting at the same time...
Peripheral receives 4 bytes from central in order to set color of 5 LEDs (1 byte command type + 3 bytes RGB data). There's an iOS app with color picker where user can select...
hi every one.
I need to load softdevice to nRF52 preview DK before execute this app follow it, but i don't know exactly how to do it.
This is my solution:
open...
Hi,
When I reset my nrf51822 beacon firmware using nrfgo, it works just fine. When I try to reset the firmware using jlink, I end up having problems. There are no errors...
Hello, I have downloaded the nRF_MDK_7_2_1, and open \Keil_v5\ARM\Device\Nordic\nrf51822\Board\pca10001\s110\ble_app_beacon\arm\ble_app_beacon with Keil_v5.
I set IROM1...
Teaching myself the Nordic libraries and API for nRF51 - going smoothly.
Keil uV5 and Dongle and SDK 9.0.0
Wanted to send my own data in the characteristic for HRM service...
The workaround for nRF51822 PAN#73 specifies setting an undocumented register at offset 0x0C0C of the timer peripheral to 1 prior to TASKS_START , and clearing it after TASKS_STOP...
Hi
I am trying to flash a new firmware into my device through DFU via the programming python script.
I use SDK7.2.0, and do:
ipy main.py -f c:\myproject.hex -a XXXXXXXXXXXX...
We are using the Nordic UART service for our product. Should we just use the standard UUID that the Nordic Uart uses or just generate our own for the product?
Thanks
Hi,
I'm working on an embedded system using PAN1026 bluetooth. I want to use the nRF APP to communicate with the bluetooth module. Currently I have:
Setup the...
To support a mix of v2 and v3 chips, I want to use the 7.x SDK. But I'm not sure it's compatible. The matrix at infocenter.nordicsemi.com/.../nRF51_Series_Compatibility_Matrix_v2...
