I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I have a dual mode BLE / ANT+ nRF51422 design going through regulatory testing for FCC / EU marketing approval. I have previously successfully tested a very similar design...
The spec of nrf52 mentiones 'Propriatary RF' as option. I was wondering if that could be used to implement 802.15.4 which would save us an entire IC and power and like basically...
Hi there!
I would like to implement the nRF24L01-module to one project.
But, it would be great, too, if i can use the application manual to use only the chip itself with...
I have the nRF51-DK development kit (PCA 10028). I'm following the gcc tutorial here - devzone.nordicsemi.com/.../.
I'm using the ble_apps_hrs project as a basis for my...
Is it possible to connect DCC / DEC4 to a transistor to turn on / off a part in my circuit? I assume yes, but I just want to make sure.
Or, is there another way to turn...
Hi again,
If I use BluetoothGATTSetCharacteristicValue and set wr_auth = 1 in the ble characteristics, I receive a BLE_GATTS_EVT_RW_AUTHORIZE_REQUEST event. I can also see...
Dear Nordic developers,
Does TWI supports bit level clock stretching? Means that after each bit (not byte) slave can hold down the clock and master should perform appropriate...
So I have the following bootloader code:
int main() {
uint32_t code;
sd_mbr_command_t mbr_command = { SD_MBR_COMMAND_INIT_SD, };
code = sd_mbr_command(&mbr_command...
My ANT BLE application runs on a custom board with a nRF51422, SD 310 rev 2.0.0
I can use the nRF UART app on an android phone, but on an iPhone with iOS 8.4 I can't even...
Hello,
I'm using an PTR5188 development board for my project which breaks out PIN 26 & 27 for ADC only. I'm using mbed as my development platform and haven't been able to...
Hi there
Can you clarify a point for me?
Quoting from Gazell link layer user guide:
"If only the ACK packet sent from the Host to the Device is lost, but both the initial...
Hello.
Reading the documentation of pstorage_load and the actual implementation has left me with confusion.
The documentation states that the size and offset parameters...
I uses S110 V6.00 softdeivce ,v5.20 SDK, and the nrf51822QFAC chip.
now I use the 32k ram ,but it is wrong.The program is not run.
I only use the 16k ram ,as same as nrf51822QFAA...
Hello everybody,
I'm trying to make TIMER1 working on nRF51822 together with softdevice.
In particular I would like to drive an interrupt line that goes to another microcontroller...
