Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi,
I have PCA10028 board, and I'm trying to implement UART send/receive.
I've searched for the problem here but could not find a solution for it.
My uart init function...
Hi
I'm using Keil V5 to program the Nordic nRF51 DK ( the one here: www.nordicsemi.com/.../nRF51-DK) but I'm a bit confused as to whether or not I need to change the settings...
I am not quite certain what the advantages/disadvantages are of using LDV vs DCDC if you are using an external regulator. In my case i use a LiPo battery outputting ~4.2V...
In the ant-to-ble bridge example in the 7.x.x SDK, there is the following comment in examples/multiprotocol/experimental_ble_ant_app_hrm/main.c :
// Need to close the ANT...
Hi all,
As I know in constant latency mode, both the regulators (1v7 & 1v2) and HFCLK are kept on. Is there a way to keep the HFCLK on while one or both the regulators...
Follow up this image. I want to reduce the negotiation time.
10:44:43.655 --> Connected to D6:9E...
10:44:45.123 --> Services Discovered
= 45.123 - 43.655 = 1.468...
when i test the ancs example application for nrf51822, i foud a question : after i disconnect the lightblue ios app with nrf51822 peripheral, the iphone still connected with...
I downloaded ble_app_lbs from GitHub. Loaded the project (on GitHub it was saved as a MicroVision 4 project) into MicroVision 5 and build with no errors or warnings.
I...
Hi sir
I want to combine heart rate, proximity and uart(proprietary) projects to one project.
As your experience, is it possible? Any side effect for that? Thanks.
J...
I have an NRF51 board running as a GATT server. Using an iOS application (LightBlue) I connect to the NRF51. If I quit the iOS application then I get a disconnect event and...
Hi guys,
I got some questions with HID over GATT on iOS/Android:
Does iOS/Android handle Telephony usage input (e.g. for phone pickup/decline)? If not, is there...
Hi I am using nRF6700 motherboard .
But when I want program nRFmodule on board1
error occure:
And I also try Module-nRF51822
There is nothing in "segger to use"
...
After I upgraded to SDK9.0. The old files still left in the project folder. I had this situation last time. What I did was recreated the project.
But is there a better way...
Hi , I tried downloading the nrf51822 softdevice and application to yunjia board which is similar in architecture to PC1001 as shown in the following links:
github.com...
I thinking that using the Company Identifiers(in MANUFACTURER SPECIFIC DATA) when Advertise being.
But Our company is not registered in the Bluetooth SIG.
Is it safe...
