Hi I'm testing the current consumption of the external qspi-flash on nrf5340dk [ MX25R6435F]. I have used ppk 2 to measure consumption with the dk and also have used a power...
Hi,
We are using nrf21540 in GPIO mode + mode pin ( and CONFIG_MPSL_FEM_NRF21540_RUNTIME_PA_GAIN_CONTROL) with an nrf52833.
We are developing under nrf connect sdk 3.0...
During the development of a Matter over Thread product, I encountered the following issue:
After adding two Matter over Thread devices (an OnOff Switch and an OnOff Light...
Hi Nordic Teams :
I would like to check the current consumption by BLE DTM.
1. Is the table measurement is from 3.0V input?
2. I find the condition in the datasheet...
HI ALL,
nrf54l15dk,v2.8.0,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
At this...
I'm developing my application with nrf 52832 and nrf SDK v17.
I know NCS is more powerful. I'm currently learning how to use it.
But now.I still need my application with...
I'm writing a wav file from the nrf52840 board to the nor flash w25q128jv with a capacity of 16mb but it seems that I can only operate on the first 2mb, even when dividing...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
Hi, I found the example of Eddystone beacon in SDK 12, but couldn't find Eddystone Configuration Service demostrated or implemented. In the legacy nrf5-sdk-for-eddystone repository...
the mcu is nrf51822，I use sdk9.0,
sdk9.0\examples\dfu\bootloader\pca10028\dual_bank_ble_s110\arm5_no_packs
In this project, I delete led，button，
change “dfu_start...
I use it. nRF52832 PCA10040 Vesion12.2.0
I am working on the ble_app_uart example as a base.
I used the sd_ble_gap_addr_set command to change the BLE address but it...
Since Google released Android Marshmallow 6.0 we are experiencing problems when connecting our nRF51822 based peripherals to a Nexus 6 phone.
The Nexus 6 is able to see our...
I use it. nRF52832 PCA10040
I have coded based on NUS.
However, I failed to pair with my Android device.
Even with ble_app_uart, the result is the same.
Hi. I'm using SDK12.2.0, S130 ver2.0.1, nRF51822AC as central.
After connection, if i use "ble_conn_state_n_centrals" function, i can get the number of connected peripherals...
my ble can send data when the data send function called inside main.c ,
But it is not sending data other than in main.c like other source files.. and getting error invalid...
I'm trying out different SDK's and some of them are working to an extent (they load the softdevice, and the app, but when I test run in debug they start at a different location...
I am working with the nRF52832 pca10040 devkit, and when I program the softdevice with the nRFgo studio, the only version that shows the firmware after programming is S132_nRF52_2...
Hi,
we are using nRF51822-QFAA in our project which is based on the PCA10000-nRF51822 Development Dongle 2.0 - layout of radio part is almost the same. I'm also using sdk...
I need to read variable length blocks from an I2C slave using a TXRX transfer. The length of the following data is given in the first read data byte, similar to SMbus Is there...
I installed Bluetooth Developer Studio , (BDS), which appears to offer a way of setting up a custom profile without have to spend too much time on writing low level code....
