Hi,
If you use the following settings, an error will occur during commissioning.
Board: Custom board
SDK:ncsv2.9.2 OS: Windows10 Sample code:Matter Lock bord target...
Hi All,
I am currently evaluating how I can charge a single cell with the nPM1300 PMIC with a USB-C connector, with the addition that the same USB-C connector should be...
Hi, on nRF54L15 Dev Kit, we are trying to validate our sleep current consumption. We are seeing sleep current of ~100-300uA, when it should be a fraction of that. As per datasheet...
I use nrf5340 DK as AP, nrf54l15 DK as TAG.
Below was uart print comments from AP
ESL_AP:~$ > esl_c bond_dump
esl_c bond_dump
Dump bonded device
ESL_AP:~$ > esl_c...
Hello,
I am implementing the Physical Activity Monitor Service which looks like this:
/* Physical Activity Monitor Service Declaration */
BT_GATT_SERVICE_DEFINE (...
We have an existing application that is based on asset tracker V2. It has been running since version 1.7.0 I have migrated to V2.9.0 a long time ago and it is running flawlessly...
We are trying to complete Bluetooth qualification on our Cycling Power Service (CPS) against the Bluetooth Test Specification (Document Number CPS.TS.1.1.1).
We fail the...
We have been working on a project that requires the following separate segments be programmed to the board:
softdevice hex file
app hex file
UICR hex file
...
Hello,
I'm currently porting all my C++ code from SD130 SDK10 to SD132 SDK12 and I also upgrading from device_manger to peer_manager.
I've noticed that in peer_manager_types...
Hello,
It seems that NRF_LOG_BACKEND_SERIAL_UART_BAUDRATE has wrong documentation. In sdk_config.h it says:
// <o> NRF_LOG_BACKEND_SERIAL_UART_BAUDRATE - Default Baudrate...
Dear Nordic Team,
Thanks for support.
I want to know the possible for nrf52832 act as a sniffer. If it is possible means i want to latest sniffer hex code.
Dear Nordic Team,
Thanks for support.
I have tested Current Time Profile sample application whenever connect with nRF connect APP the debug widows shows always "Current...
Good morning all,
We have a circuit based on 51822 chip.
We are currently trying to monitor some value from 0v to 24v from the analog inputs.
It's working, however...
I recently saw that SDK12.0 provides a Bootloader Cryptography module. I'm not certain after reading the documentation that this module can support my use case:
infocenter...
Hi,all. i want to use nrf51822 to generate a 3.3M hz wave,but i don't know how to do this.Can this chip reach so high frequency？Can someone help me? Thanks ！
I'm trying to implement context switching from handler mode to thread mode using PendSV. I set the PendSV pending bit inside an ISR with SCB->ICSR = SCB->ICSR | SCB_ICSR_PENDSVSET_Msk...
Compiling nordic project I get errors:
compiling main.c...
..\..\..\main.c(37): error: #5: cannot open source input file "softdevice_handler.h": No such file or directory...
I am not sure if this is a limitation with Keil or Nordic SDK. I made another copy of ble_app_uart inside SDK_11 s130 and renamed it with a much longer name. I tested that...
I'm using the nRF SDK5 v11.0.0.
I'm trying to test out UART Logging in the simple blinky example bundled in the SDK.
I added NRF_LOG_INIT() and then a NRF_LOG("Testing\n...
Hello everyone,
I am trying to implement a bootloader to my application to be able to enter in DFU mode.
I am using nrf51822 (32KB ram 256 flash) and s130.
I have taken...
My understanding is that the nRF51 is known to need a fairly stiff external pull-down resistor on SWCLK to avoid noise putting the chip into debug mode. I note that the nRF52...
